Glue for paper wallpaper for painting. Wallpaper for painting: how to glue and paint. How to choose wallpaper for painting

It is difficult to answer the question of which is better - wallpapering or painting the walls. There are pros and cons in both cases, many factors should be taken into account here.

Choosing what will be better - painting the walls or sticking wallpaper, remember that your decision depends not only on the harmonious combination of furniture, textiles, and accessories. The main role in this matter is decided by practicality, efficiency and speed of work.

If you want to make the apartment cozy, aesthetically flawless and with the possibility of changing the interior - stick wallpaper for painting the walls. They are more practical, since there is always a possibility of peeling on surfaces treated with paint - either the putty did not stick to the base, or the wall had significant cracks. The appeared defect is immediately visible, and it will have to be repaired. And if such an incident happens under the wallpaper, you will know about it only when you peel it off.

If you want to work with a brush or roller directly on the walls, prepare the base for painting flawlessly and buy high-quality material for work. You should be aware that wall painting is not cheaper than wallpapering, and in some cases significantly more expensive.

Varieties of wallpaper for painting

This type of coating is made from various materials. When wondering what kind of wallpaper for painting is better to use, keep this in mind. Manufacturers offer the consumer canvases that can be dyed a certain number of times:

from paper;
non-woven;
vinyl;
fiberglass.

Your choice depends on the purpose of the room. So, paper sheets should not be used in the bathroom - they are afraid of moisture. In this case, it is better to glue non-woven, vinyl wallpaper for painting - they are not afraid of water.

The modern market presents a huge number of options that can satisfy the aesthetic needs of any buyer. Before choosing wallpaper for painting, it will not be superfluous to know what types they are produced.

The manufacturer produces light gray or white wallpaper for painting, so that the color tone of the color you choose does not change on the canvas. These shades are considered neutral.

Wallpaper painting tools

For work, not only high-quality materials are required, but also a good tool.

In order to qualitatively paint the wallpaper for painting, you need a little experience. Pre-practice on a small piece of canvas, but not on the wall to be painted. Carefully roll the roller in a ditch so that the paint is evenly distributed over the entire surface of the tool.

Now let's figure out how to properly paint wallpaper for painting. All sheets differ in their texture, in characteristics. This means that not only the pasting process, but also painting will be different.

All painting work is regulated by regulatory documents and must comply with:

paper wallpaper

These canvases are absolutely safe in terms of environmental friendliness. Paper wallpaper for painting is produced from several layers of paper. Their quantity and qualitative composition directly affects the density of the sheet. For painting, two-layer wallpaper is used, having a natural filling of wood chips, which gives the canvas additional relief. Information about the material can be found in the article "".

Do not be afraid of soaking the paper web from paint. Please read the insert carefully before making a purchase. The manufacturer indicated that the surface is covered with a water-repellent composition - which means that the paint will not wash out the glue and will not soak the paper. You can safely buy such rolls, glue them and paint.

Canvases are produced GOST 6810-2002, they come in two colors:

Grey. This product produced from waste.
White. Products are made of plain paper.

Recycled canvases are cheaper, but there is no significant difference between these options.

pasting

The pasting process is described in the article "". First you need to mark the wall. The location of other canvases depends on how the first sheet lies correctly. Then cut the sheets to size, coat them with glue and wait until they are saturated with the composition. The walls also need to be coated with glue. Attach the measured sheets to the surface and glue with the help of tools.

Coloring paper sheets

Paint for paper wallpaper produced on the basis of water. If you are wondering if it is possible to paint the wallpaper not for painting, then we answer that it is possible, but not necessary. The sheets will become limp and fall off, as they are not treated with a special water-repellent composition.

Before deciding which paint to paint the wallpaper, look at the variety table presented. coloring compositions, which you can use during the repair of your apartment or house.

Manufacturers, in addition to all kinds of colors, offer the consumer basic and white paint. They are the same in color. But the latter has pigment, while the base does not. With the help of tinting paste, you can tint yourself or turn to specialists.

Self-tinting should be carried out for the entire volume of paint, since it is impossible to repeat the same shade a second time by hand. And special machines will mix the paint with the color scheme, automatically selecting the volume and color.

The whole algorithm of work is compiled in the following sequence:

If the room is very dry, then in order for the paint not to dry quickly, it is necessary to increase the humidity of the air. To do this, 30 minutes before the start of work, bring dishes with hot water, and place a wet terry towel over the batteries. Doors and windows must be tightly closed. So you can paint the walls without fear of premature drying of the paint - it will lie on the base in an even layer.

Just do not forget that the wallpaper is pasted on a water-soluble adhesive and a long stay in a humid environment can lead to peeling.

Paper wallpaper in the interior

Surface care

Cleaning paper wallpaper for painting depends on the quality of the paint. If it is water-based, then the walls are wiped with a damp cloth, and surfaces painted with acrylic or latex compounds can be gently rinsed without strong pressure on the surface. It is allowed to add a small amount of non-abrasive detergent to a bowl of warm water.

It is worth remembering at the same time that even the most dense wallpaper made of paper is afraid of moisture.

Therefore, if possible, try to remove dirt with an eraser, but do not rub hard. Grease stains are removed only fresh - you should apply a clean cloth and iron the fabric with a slightly warm iron or wipe the stain with pulp white bread. Continue these steps until the contamination disappears. Don't forget to change napkins and bread.

Non-woven wallpaper

This product belongs to the class of anti-vandal product, consists of cellulose and binders, meets quality standards GOST 6810-2002. Many people call it "improved paper", which is true. You can read about the characteristics of the coating in the article "", here we only note that:

the canvas allows you to hide the defects of the base;
easy to clean with special detergents;
it is resistant to abrasion;
during operation is not deformed;
not afraid of water;
subjected to repeated coloring.

Similar wallpapers for painting in the interior are recommended for any premises. They look great in the living room, but are also indispensable for the kitchen and bathroom. Only in the latter case, do not use water-based compositions for painting - they are afraid of water.

To paint old wallpapers, you first need to make sure of their quality, to understand that they will not fall off in six months. If the canvases hold well, you can safely engage in painting work:

prepare the surface;
stir the paint;
paint over hard-to-reach places with a brush;
to treat the surface with a roller;
apply the next coat of paint to the wall.

pasting

How to glue wallpaper for painting is discussed in detail in the materials of the article "". First you need to mark the walls, it is important to correctly position the first sheet, since it depends on it how other canvases will lie further. Then cut the sheets to size, coat the surface with glue, attach them to the wall - stick.

Coloring

Is it possible to paint non-woven wallpaper with oil paints or solvent-based compositions? No, these compounds are capable of destroying the texture and the top layer. As a result, you will have to re-glue the walls, and this will entail additional expenses. Money, strength and time. If you want to know how to paint the wallpaper with water-based paint, then the painting processes are carried out in the same sequence as when working with acrylic or latex composition:

Non-woven wallpaper is a very interesting wall material. You can experiment with them:

Apply paint to the wall before gluing them. Only in this case choose a bright shade.
Paint wallpaper from the wrong side. This method emphasizes the bulge and texture of the pattern.
On the surface pasted over with textured canvases, paint is evenly applied, and then its excess is removed with a soft sponge. Thus, the effect of visual volume is obtained.

You can paint the wallpaper up to seven times, as long as the texture of the canvas allows. The last painting will completely level the relief.

Caring for non-woven wallpaper

They can be cleaned with special nozzles of a vacuum cleaner or with a wet sponge. Be sure to pay attention to the quality of the paint. If it is acrylic or latex, then the surface can be washed with water at room temperature with the addition of a small amount of liquid non-abrasive cleaner or soapy water. And surfaces treated with a water-based emulsion should be wiped with a slightly damp soft sponge or it is better to vacuum with a carpet nozzle.

Vinyl wallpapers

These wall coverings comply with GOST 6810-2002, have two layers: the top is made of polymer material and is the front side of the coating, and the bottom is either paper or interlining.

Answering the question whether it is possible to paint vinyl wallpaper, we say yes, if they have a non-woven base. paper base not suitable for painting, it quickly soaks and deteriorates.

pasting

The gluing process is described in detail in the material "". The work will consist of the following cycles: you first need to mark the walls, then cut the sheets to size, coat the canvas and walls with glue, attach the sheets to the surface and glue.

Painting vinyl wallpaper

Vinyl wallpaper for painting on a non-woven base is not so easy to paint, especially if you do it for the first time.

The top layer of the sheet consists of foamed vinyl and has a pronounced embossed surface, on which the paint is difficult to apply evenly.

Therefore, be sure to prime the wall once or better twice. And then on the following technology:

As you can see, even a non-specialist can paint non-woven vinyl wallpaper. You just need quality material, tools, right technology, desire and a little training. We are confident that in the presence of all these factors, you will independently cope with this work.

Vinyl wallpaper in the interior

Caring for vinyl wallpaper

Vinyl wall coverings are cleaned with a sponge dampened with a mild soapy solution. Fingerprints, grease and water stains are easily washed off. The surface does not need to be rubbed hard or abrasive or containing bleaches and organic solvents compositions.

To wash the remnants off the wall detergents, wipe them from top to bottom with a sponge plain water and wipe off moisture with a dry towel.

Any kind of contamination must be cleaned from the edge to the center. If you're not sure about a cleaner, try using it in an inconspicuous place first.

Glass fiber for painting

This wall covering is an eco-friendly roll material, which is produced by GOST R 52805-2007. The top layer is glass fabric obtained in melting furnaces at a temperature of 1200 °C. The coating on the front side has a clearly expressed varied texture. Information on the production of glass and specifications presented in the article "".

Glass fiber - all kinds of texture

The surface is designed for 20 times painting without fear of damage to the texture of the coating.

pasting

A detailed process for performing work is described in the article "". We pre-mark the walls, cut the sheets to size, coat the wall with glue, apply the canvas to the surface and glue it.

Glass fiber coloring

Paint for glass wall paper intended for painting must be water-based and have high rates wear resistance. Compositions created on alcohol solutions are not suitable - they are difficult to apply on a corrugated coating and the pattern quickly turns into a smooth surface.

When purchasing paint, pay attention to the external conditions in which the painted surface will be used and the possibility of its mechanical damage.

Among the manufacturers I would like to note the most popular: Joker, Harmony, Tikkurila, Dufa, Dulux Bindo 7. Give preference to glossy finishes, they look more impressive in the interior.

Acrylic compositions differs in that it forms a shiny, abrasion-resistant surface. They are based on styrene-butadiene and fully preserve the qualities of fiberglass without changing the texture of the fabrics.
latex paints such as Dufa Mattlatex, Tikkurila Euro 7 have a matte effect and are designed for walls in dry rooms. They endure easy wash, resistant to abrasion, economical in consumption.
Water-based compositions also suitable for fiberglass, only they do not need to be used in rooms where humidity is high.

Before painting, the walls must be primed with a special compound. Also suitable for these purposes wallpaper glue, which is diluted with plenty of water. The required volume must be indicated on the package.

Glass fiber care

Over time, the canvases do not lose their shape and color. They withstand almost all manufactured detergents. What you need to pay attention to is the properties of the paint. Water emulsion does not need to be washed even with plain water.

How to choose wallpaper for painting

Going to the store for shopping, you should pay attention to the following factors:

Expert opinion site

As you can see, painting work can be done on your own with ordinary tools or fixtures, without the help of professional finishers. It is important to choose the right wallpaper for painting according to their technical indicators and characteristics: paper is recommended in the nursery, non-woven in the kitchen. Know how to glue and paint them. To do this, you should carefully read the relevant articles on our site. Assume that with regard to painting, they are compiled on the basis of TTK "Typical technological map for water-based and oil painting of walls and ceilings", developed in the Mosorgstroy trust in 1983. And the correct wallpapering technology is described in our other materials.

Observations have shown that in offices and public institutions where there is a lot of traffic, non-woven or glass wallpaper for painting is most often used, in rooms where a person sleeps and rests, paper coverings are preferred, it is better to paste over living rooms and kitchens with vinyl. By following our recommendations, which comply with all-Russian quality standards, you will finish your repair quickly and without further problems.

Wallpaper is the most common type decorative finishes walls, often to update modern interior apartments and office space are used . Usually non-woven wallpaper is unpainted, that is, they have White color, which further reveals design ideas to create an individual interior. Having made a choice in favor of this, the question arises, how to glue non-woven wallpaper for painting on the wall, so that it turns out beautifully and with high quality? But in order to answer it, you need to know what advantages this finishing material has:

do not stretch;
durable non-woven base, but it is easily cut with scissors;
Gluing them is quite easy, no more difficult than ordinary paper wallpaper.

Non-woven wallpaper pasting technology, preparation

For gluing non-woven wallpaper in the same way as for other types of wallpaper: the surface must be clean, even, primed and puttied. When gluing wallpaper for painting, you can leave only the smallest scratches, chips and bumps, it is better to fix the rest of the flaws in the wall. If there is a plinth, it is better to dismantle it.

For gluing non-woven wallpaper, you will need traditional tools used in working with wallpaper:

Ruler and pencil;
roulette;
stationery knife with spare blades;
level;
rollers;
cuts of soft tissue;
a couple of tanks for glue;
a small ladder or stepladder.

Strictly according to the instructions. It is advisable to use special adhesive composition designed for non-woven wallpaper. It is more oily and viscous than other types of wallpaper glue, which is why it does not absorb into the base for quite a long time.

It is important to know that the glue is applied only to the wall, in no case to the wallpaper, although there is an opinion among the people that for reliability it is better to apply glue when gluing non-woven wallpaper both on the wall and on the canvas, but the layer of glue should not be excessive. With excess glue, it will shrink, which will lead to the formation of unnecessary cracks at the joints of the wallpaper strips and it will still be squeezed out from under the wallpaper when ironed with a wallpaper roller.

Wallpaper is prepared by cutting the roll into strips 5-7 cm longer than the required height. If customization of the pattern is required, the value of rapport is added to the length of the canvases. Glue on the walls is evenly applied with a roller and in the corners with a brush. In order not to accidentally smear the already glued canvases, the adhesive composition is distributed 10 cm wider than the strip itself. But if suddenly this happened, it can be erased with a regular soft sponge.

How to start gluing non-woven wallpaper for painting

Wall pasting starts from a window or corner, slowly moving deeper into the room. The first strip of wallpaper is marked and glued strictly according to the level, it is she who sets the direction for all other canvases. The canvas is gently brought to the surface smeared with glue and pressed upper part Please note do not paste the wallpaper upside down. The edge of the strip should lie strictly along the drawn line. Then, with a plastic spatula, the wallpaper is smoothed from the center to the edges so that there are no wrinkles and bubbles. Make sure that the wallpaper is glued evenly and well fixed. Cut off the excess length from the bottom with a clerical knife. There is no need to worry about the cut line being perfectly even, because the plinth will close it. If the wallpaper lays unevenly, it can be quickly peeled off and pasted again. Non-woven wallpaper "glide" on the wall smeared with glue, which makes it possible to move the canvas and adjust the docking.

The second and subsequent canvases are glued, guided by the first, always end-to-end, without overlap.

Each strip of wallpaper is not glued all at once, but holding one edge at a small distance from the wall, the other is joined to the already pasted canvas. It is important to avoid overlapping edges and at the same time avoid gaps between them. The correct joint is almost imperceptible.

A joint is always needed in the corners, you should not try to seal it with just one strip. If the corner is even, the edges of the canvases are glued with a slight overlap, then, pressing the spatula against the wall, they cut the corner, remove the excess and glue the wallpaper end-to-end. If gaps have formed in the corner, narrow strips of wallpaper are glued under the canvases.

How to paint glued non-woven wallpaper

As already mentioned, white non-woven wallpaper is produced mainly for painting, if they have a smooth surface, they do not need to be joined. To paint them, you will need water-dispersion, water-based latex or acrylic paint. When painting in several layers, the color of the paint should be chosen a couple of tones lighter. You can paint with an ordinary roller, preferably from foam rubber. Areas near the joints with the ceiling, baseboard or windows are painted with a brush to achieve maximum accuracy.

In order for only one layer to be enough when painting the wallpaper, it is better to make the last layer of soil colored. Just add a little paint to the primer of the color you are going to paint the wallpaper with. This primer is applied with a roller after the last sanding.

In addition to white textured non-woven wallpaper, there are smooth non-woven wallpaper for painting. They are easier to paint, but visually they are inferior to wallpaper with embossed vinyl coating.

It is possible to paint non-woven wallpaper only a few days after gluing.

There are two popular ways to create a decorative wall covering.

Non-woven wallpaper is painted on the reverse side and only then glued, which will change the color of the wallpaper for the better and elegantly highlight the vinyl reliefs. You can also paint the wall itself before gluing.

Only vinyl reliefs are painted with a rigid, lint-free roller. This will accentuate them and make painting much easier.

You can make the paint layer even smoother with a spray gun. When painting wallpaper with a non-woven base repeatedly, be sure to wait until the previous layer has dried before applying the next layers.

During the renovation process, you have chosen finishing materials on the . We studied the types of wallpaper for painting, chose and purchased the right one, and are ready to start repairs. Don't rush, buying wallpaper isn't everything preparatory work. Before starting the actual gluing, it is necessary to choose the right glue and paint for the wallpaper.

The choice of glue and paint for wallpaper

The choice of paint for wallpaper depends not only on color wishes. The main selection criteria are the type of wallpaper used and the purpose of the room. So, for example, water-soluble paint is much cheaper than other analogues, but the use of such paint in a humid room will lead to damage to the coating. This type of paint can be used in places where water does not get. Non-woven, vinyl and paper wallpapers are covered with water-based paint, for pick up latex or acrylic paint. The acrylic version is the most versatile and durable, the coating is not afraid of moisture, is resistant to abrasion, the paint can be used in wet rooms (bathroom and kitchen), and in rooms with a high load on the walls (hallway). Latex paint shows the same characteristics as acrylic, the difference in appearance: acrylic matte, latex glossy. Treat the choice of wallpaper glue as responsibly as the purchase of paint. Incorrectly selected glue will lead to peeling of the wallpaper. Paper wallpaper holds vinyl glue perfectly, it dries for a long time, which gives time to correct a thin canvas. For non-woven wallpaper, choose a special non-woven adhesive. Fiberglass wallpapers will also require specialized glue, they are heavy and other glue will not hold them on the wall, and even more so on the ceiling.

Wallpapering for painting

The process of wallpapering for painting is generally similar to wallpapering with ordinary wallpaper, however, there are several nuances that must be taken into account before starting work.

Substrate preparation does not require careful leveling, but if there are sharp or large drops, the walls will have to be trimmed. In addition, it is desirable to bring the walls to the same color so that the color scheme lies the same over the entire area of painting.
If the walls were previously painted, then water-based paint enough to wipe with a rag, but oil paint will have to be removed.
Dismantle sockets and switches, turn off electricity, cover places with wires with polyethylene.

Cut the wallpaper 5 cm more than the height of the ceilings so that you can fit the pattern. With a complex pattern, do not cut the wallpaper for future use, cut one strip at a time. When working with glass fiber, do not forget about a respirator and gloves; when cutting, small crumbs should not get on the skin or mucous membranes.

When sticking paper wallpaper, apply glue on the wall and on the canvas; for non-woven and glass wallpapers, glue on the base is enough.
Wallpaper for painting glue only butt-to-butt. Places glued with an overlap, after staining, will stand out visually.
Secret from designers: glue non-woven wallpaper parallel to the floor. This arrangement will make the final coating visually solid.

Wallpaper painting

The process of painting wallpaper also has several features, the implementation of which will help make the final coating perfect.

In order for the wallpaper paint to lie evenly, it is important to wait for the canvas to dry completely on the wall. Depending on the conditions of humidity and temperature in the room, this stage will take 2-3 days. But manufacturers do not recommend delaying painting until dust and particles of dirt have settled on the wallpaper.
Work hard-to-reach places with a brush, paint the rest of the area with a roller. Do not apply paint multiple times in the same place to avoid uneven staining.

There are several technologies for painting wallpaper. Painting over the wallpaper will give a uniform shade. Coloring the inside of the canvas gives an unusual soft tint to the background. Complex two-tone staining is available when using deep reliefs, when the protruding parts are washed off the paint and covered with a different tone.
When painting glass wall paper, apply a thin layer of primer first to reduce the amount of paint absorption by the material.

Pasting walls with wallpaper under paint is a universal way to decorate the interior with a practical and durable finish.

The topic of this post will be non-woven wallpaper. In any repair, there always comes a climax when the ceilings and walls are plastered, primed, and ready for wallpapering.

There are many types of wallpapers with different structures, bases, various colors, various patterns, but sometimes you yourself want to not only paste the wallpaper, but also paint it in the color you want, there is such an opportunity. To obtain high-quality painting in interiors, walls and ceilings are pasted over with non-woven wallpaper.

Non-woven wallpaper for painting have many advantages: they are non-toxic, fireproof, cover small flaws (scratches, roughness, microcracks), withstand minor mechanical loads, are resistant to tears and stretch marks, create a uniform substrate for painting and do not require great skill in work. Non-woven wallpaper for painting is made from compressed cellulose fibers, paper and additives.

On the wallpaper market, they are presented in different options, starting with smooth and ending with textured ones, also have different densities (the higher it is, the stronger the material is resistant to deformations of the base). Once you have made your choice, you can get to work. Before wallpapering, if it is just replacing the wallpaper in the room, do not forget to turn off the power at the power panel and remove the panels from the sockets and switches.

Sticking non-woven wallpaper requires little knowledge and skill. The base must be properly puttied and primed before gluing. Before proceeding directly to gluing, prepare an adhesive designed for non-woven wallpaper, and mark the walls or ceilings (depending on what you are gluing). Basically, the rolls have a width of 1.06 m and a length of 25 m, so the markings are made from the corners for the first strip - 1.04 m, giving an allowance of about 2 cm for trimming.

Many advise not to cut the strips, but to glue them directly to the wall, while cutting the roll at the bottom, but for ease of use it will be better if the strips are cut in advance (do not forget to add 2-4 cm in height to the strip for trimming at the top and bottom). For the correct direction of the strips along the level, put two or three marks with a pencil along the plumb line (photo 1).

Glue for non-woven wallpaper is applied to the wall, this is one of the pluses and you do not need to apply glue to the wallpaper and wait a certain time for their impregnation. The corners are smeared with a brush (photo 2), and it is better to apply glue on the base itself with a roller with a pile of about 8-12 mm (photo 3), creating a uniform layer.

After the glue is applied, the strip is set according to the level or plumb marks (photo 4) and carefully leveled over the entire area (photo 5).

Air is expelled with a special plastic spatula in the direction from the center of the strip up and down (photo 6).

Wallpaper allowances in the corners are cut with a metal spatula and a paint knife (photo 7).

Excess glue should be thoroughly washed with warm water using a foam sponge. The next strip is glued end-to-end with the previous strip. If the walls have protruding parts (slopes), the strip can be wrapped rather than cut off (photo 8).

In this case, the air is expelled from the outer corner into the corner of the wall (photo 9). After complete drying, the seams of the wallpaper are puttied with finishing acrylic putty, if used. non-woven wallpaper for painting with a smooth texture (photo 10).

When the putty dries, it is cleaned with fine sandpaper or an abrasive mesh and primed (only seams). That, in principle, is all the wisdom of gluing non-woven wallpaper for painting. In a day non-woven wallpaper Ready to paint and ready to paint.

Today we will consider in detail how to glue and paint wallpaper for painting. After all, if this work is not done correctly, then you can ruin the surface, because all the flaws will be visible. And how to glue the wallpaper for painting, we will consider below. Also on the video and photo you can see the most difficult areas of work.

Wallpaper for painting how to glue is determined by the composition of the wallpaper itself. After all, in the retail trade there are quite a few materials that are quite different in composition.

The price of new materials will be much higher, because their characteristics are the most acceptable. The cheapest ones are paper ones (see Let's consider how to glue paper wallpapers correctly). But for example, they should not be fixed in the kitchen. After all, they are quite susceptible to a humid environment.

Let's look at the most common types of wallpaper and decide which ones are right for you:

Paper	The cheapest and most short-lived. This type of wallpaper is of low quality, so they are often used to create the background of the main interior. Paper wallpaper for painting is glued to the wall in the same way as ordinary wallpaper, but still, for subsequent painting, it is more expedient to choose a better base.
Vinyl with paper backing	This type of wallpaper for painting consists of a paper base and a vinyl textured layer. They are of higher quality, but vinyl is not durable and wears out quickly, so for long-term use of such wallpapers, it is necessary to apply paint or varnish to them.
Non-woven wallpaper	This type wallpaper can be used not only for painting, but also as a finished material for the wall. They consist of two layers - a non-woven base and a vinyl layer with a textured surface. The wallpapers of the American manufacturer York have proven themselves in this category. They have very high quality characteristics, while not creating any particular difficulties when working with them. Non-woven wallpaper is high-strength and pulls walls well. In addition, it becomes possible to save glue by applying it directly to the wall.
Glass fiber	Glass fiber is produced by combining a paper base and fiberglass threads, which contain quartz sand with special additives. These wallpapers are characterized by a dense structure and clear embossed lines. The interlacing of fiberglass threads forms various ornaments on the wallpaper. This type of wallpaper for painting is the most durable and durable (see How to glue glass wallpaper for painting: do it yourself), they can be washed, so this a good option for rooms where there are small children or pets. In addition, another important plus of glass fiber is their fire resistance.

The procedure for gluing wallpaper for painting

Wallpapering for painting is done in a certain order. There is nothing complicated here, but the instruction must be followed.

So:

How to glue wallpaper for painting should be determined on initial stage. After all, they can be different not only in length, but also in the placement of the picture. So immediately it will be necessary to make markings and cut the rolls into strips.
Now we beat off the first line for gluing. To correctly determine it, you need to apply a plumb line. After all, it is on the first strip that the rest will be attached.

Attention: The larger the drawing, the more waste there will be. This factor must be taken into account when purchasing materials.
Training Before starting work, you need to prepare inventory, the wallpaper itself, and glue suitable for this type of material.
From the tools you need a roller or a wide soft brush for applying glue to the wallpaper, and the same tools for subsequent painting of the wallpaper. You can use a spray gun (see Paint spray gun: features of use).
For work, you need to prepare a bucket or other container for diluting glue, and a container for paint. You also need to prepare a soft cloth in advance to remove excess glue.

Adhesive selection An important point in organizing wallpapering for painting is the choice of a suitable adhesive composition.
Plain paper wallpapers can be glued with ordinary wallpaper glue, consisting of methylcellulose. Even a paste prepared on their own is suitable for them.
To work with heavier material, it is necessary to use specially designed adhesives.
PVA-based compositions are a universal tool for gluing heavy wallpaper or york wallpaper. They are especially reliable and can hold heavy and dense two-layer wallpaper sheets on the walls and even on the ceiling.

wallpaper sticker The procedure itself is practically no different from the standard algorithm for pasting walls, and includes several stages:
Cut the roll into strips. The height of the finished strips should be 10-15 centimeters more than the height of the room. Thick wallpaper can be cut with a sharp knife or scissors for cutting metal. Further along the wall, at a distance of approximately 50 cm from the window, it is necessary to draw a vertical reference line perpendicular to the floor surface.
Coat the strips with glue. Here you should consider your own characteristics for each type of wallpaper. So, paper wallpaper is smeared with glue on the reverse side and left to soak. Be sure to apply glue to the wall. The sticker of non-woven wallpaper requires priming the wall surface, the glue should also be applied to the canvas and to the wall. In order to glue glass wallpaper, it is enough to smear the wall with glue.

Stick wallpaper. The strip of wallpaper attached to the wall must be aligned with a vertical reference point, and begin to smooth it with a soft cloth to get rid of air bubbles and other irregularities. The following strips must be glued end-to-end in the direction from the window. special attention requires gluing corners - here it is necessary to overlap, when gluing the first strip, a margin of 2-3 cm is made, the second strip is glued on top.

Pasting paper and vinyl wallpaper for painting
To work with this type of wallpaper, you need a special glue, in accordance with the recommendations on the package.
The strips need to be glued back to back, because the wallpaper for subsequent painting is quite thick and when overlapping the strips, the seams will be very noticeable.
Glue is applied to the prepared strip, then folded over both edges to the middle, and left for impregnation for no more than 15 minutes.

Attention: It is very important to ensure that there is not too much glue, otherwise the canvas may tear or lose its texture. To level and adjust the wallpaper, you can use a rubber roller or a plastic spatula.

Gluing non-woven and glass wallpaper for painting
It is much easier to work with non-woven or glass wallpapers, because the glue designed specifically for these types of wallpaper is applied only to the wall. This saves a lot of time as there is no need to wait for the wallpaper to soak.
Glue should be wider than the width of the strip, a section of the wall, to which the wallpaper is then applied. Another positive point in using wallpaper of this type is that they do not need to be cut in advance. The roll is applied to the wall, unwound to the desired length and cut off. However, if you want to customize the pattern, then the wallpaper will still have to be cut.
When sticking any type of wallpaper for painting, it is necessary that the temperature in the room is not lower than 20 degrees C, and a prerequisite is the absence of drafts until the wallpaper is completely dry. It should be noted that glass wall paper takes longer to dry than other wallpaper for painting. You can apply paint on the wallpaper not earlier than in a day, but be sure when they are completely dry.

Coloring pasted wallpaper
Provided that the surface has already dried, you can start painting the wallpaper. For any type of wallpaper, you can use paints that do not contain chemical solvents.
Used to color paper wallpaper. water-dispersion paint. For non-woven and vinyl - water-based. Acrylic and latex emulsions are suitable for coloring glass.
The paint must be evenly distributed over the entire canvas. In order not to spoil the relief of the wallpaper, you should not paint the same place several times.
Re-painting the surface is permissible only when the first layer is completely dry.
The use of wallpaper for painting makes it possible to update the interior without global repair work. The paint color can be changed up to 8 times, which makes it easy to refresh the environment, create original design solutions to make the interior practical and modern.

Wallpaper for painting how to glue you now know. The most important thing is not to rush and use only high-quality materials when working. After all, this will be the key to success and durability of the coating.