How to remove stuck items from the washing machine? Object Retrieval Tool Behind the Cabinet How to Remove a Foreign Object from the Washing Machine

You will find a list of them at the bottom of the page.

A foreign object that gets into the ear can cause a lot of inconvenience. For example, some children like to put various small objects in their ears that can get stuck in the ear canal. Fortunately, in most cases, you can get them yourself without hearing loss or any other health consequences. However, if you can't see what's in your ear, you should see a doctor.

Steps

Part 1

Preliminary preparation

Find out exactly what is stuck in your ear. We cannot always find out how this or that object ended up in the ear, but our actions depend on the type of this object. Before taking any further action, try to determine what is in the ear.

Determine if you need immediate medical attention. Although a foreign object in the ear is annoying and uncomfortable, it is usually not a medical emergency. If you are unable to remove the object yourself, you can see a doctor the next morning. However, in some cases, immediate medical attention is required to prevent more serious damage.

Know what not to do. Often the irritation caused by a foreign object is so great that we begin to act feverishly without thinking about the situation. However, many actions that seem obvious at first glance can do more harm than good.

Part 3

Health care

Prepare for your doctor's visit. If the home remedies and methods listed above do not work, you should seek medical help. Before visiting the doctor, gather all the necessary information. If a foreign object is stuck in the child's ear, ask him more about how it happened. Your child may be more willing to tell you about it than the doctor.

Be sure to let your doctor know exactly what is in the ear and how long it stays there. Based on this information, the doctor will be able to assess the degree of risk.
You should also tell your doctor about what happened after the foreign object was in your ear. Have any side effects? Have you tried to retrieve the item yourself? If yes, what did you do?

Ear washing. To remove the foreign object, your doctor may suggest that you flush your ear canal with water or saline. This is a fairly quick and simple procedure.

Let the doctor remove the foreign object with medical tweezers. Although you may not be able to do this at home, the doctor uses special tools that are more appropriate for the case.

The doctor may try to remove the foreign object by sucking it through the tube. To do this, he will bring a small catheter to the stuck object. By sucking air through the catheter tube, he can gently remove the foreign object.
- As a rule, this method is used to extract solid objects (buttons, beads, etc.). It is less suitable for crumbly organic objects or insects.
Get ready to apply anesthesia. It is often used to calm infants and young children, as the patient must not move during the procedure. In this case, doctors often recommend suitable anesthesia, because one careless movement of the patient can damage the delicate tissues inside the ear.

Follow your doctor's instructions if you have a pierced eardrum. A foreign object can pierce the eardrum. In this case, the doctor will prescribe the appropriate treatment.

Talk to your doctor about the treatment you need. After removing a foreign object from your ear, your doctor may recommend that you do not swim or wet your ear for 7 to 10 days. This will protect you from infection. When taking a shower or bath, lubricate the damaged ear with petroleum jelly and plug it with a cotton swab.

How to get a foreign object out of LG washing machine ? We all faced the problem of getting a foreign object into the washing machine. They get there along with clothes whose pockets you have not checked, or which have not been placed in a special laundry bag. Foreign objects can simply be in the drum with laundry or get stuck at the bottom of the tank, in the nozzle, and also wound around the shaft.
Today we will figure out how we can get him a bone from a bra that has fallen to the bottom of the tank.

In order to get a foreign object out of the LG brand washing machine, you will need:

Pliers;
Head for 10;
Slotted screwdriver;
Crosshead screwdriver;
Medical clips;
Flashlight.

First we need to find the place where the bone fell. It is necessary to open the hatch door and twist the drum in different directions. You will immediately hear an extraneous knock or noise. Sometimes through the openings of the tank you can even see where the foreign object is. Be sure to check the gap between the tank and the cuff, the bone may be there and create noise when the drum rotates. If there is no bone between the cuff and the tank, then it is necessary to disassemble washing machine.

It is much easier to get a foreign object out of a front-loading machine. This is done through a heating element. In top-loading machines, there is a special compartment for cleaning.

In order to disassemble the washing machine, you need to remove the back panel. If it is missing, then the front panel is removed accordingly. Then we need to remove the belt that drives the drum and find the heating element. It is very important to remember in what order the chips are installed on the heating element. Then you need to unscrew the chips and remove the heating element. Through the resulting hole, you can remove the bone.

You can clearly see how to remove a foreign object on our channel:

Very often, due to the negligence of the user, foreign objects get into the washing machine. It's one thing if this object gets into the drum and spins along with the laundry, and quite another when a foreign thing gets stuck in the tank. In both cases, you need to act immediately and get something that should not be in the car. How to do this, we will now describe in detail.

How did the item get into the car?

First of all, it must be said why foreign objects appear in the washing machine. They get into the car along with clothes whose pockets you are too lazy to check. The most common item is money, or rather coins, although paper ones also sometimes fall into the drum. In addition, some managed to get a passport, telephone, gold chain and rings. Often, the masters of service centers pull seeds, pins, bolts, nuts, hairpins out of the car.

In addition to items that fall out of the pockets of clothes, parts of the clothes themselves can get stuck in the washing machine. The most common are buttons, beads and rhinestones, as well as underwire from a bra.

A foreign object can get into the machine and not only with clothes. It can be put into the drum by small children or pets. An object can get inside the washer not only through the drum, but also through the powder cuvette.

For your information! In some models of automatic washing machines, small things can get stuck in the tub because there is too large an opening between the tub and the drum.

Any foreign object that gets into the washing machine either remains in the drum until the end of the wash, or:

falls to the bottom of the tank;
gets stuck in the tank;
is wound on a shaft.

Removing the object from the drum

How to remove a random object from the machine drum if you noticed it back in
start washing? Everything is quite simple - you need to cancel the program. In most cases, you need to do the following:

press the start (pause) button of the program, as a result of which the machine will stop;
press the program start (pause) button again and hold for about 5 seconds;
wait until the pump pumps out water and the machine turns off.

In some washing machines the water is not drained, so after the program is turned off, the water must be drained manually. This can be done through the emergency drain (small hose next to the drain filter) or through the filter located at the bottom of the machine. Draining the water is necessary to unlock the hatch door lock. After the work done, you can open the drum and get a foreign object.

Important! It is not worth resetting the program in the washing machine by pulling the plug out of the socket, firstly, this may affect the control module, and secondly, modern machines remember the selected mode and continue the program from the point of stop after the power supply appears.

What to do if it is stuck in the tank

If a foreign object has fallen into the tank or is stuck between the tank and the drum. It won't be easy to pull it out. It is easy to understand that there is something in the tank, you will notice an extraneous sound when the drum is rotated by hand, unless, of course, it is a handkerchief or sock. But even soft objects should not remain inside the washer, sooner or later they will manifest themselves, blocking the operation of the drain pump or the rotation of the drum.

Get an item from washing machine can:

through the drain filter;
hole for heater.

Small objects such as pins, nuts, coins, etc. can pass through the drain pipe and enter the filter. Removing them from the filter is quite simple. Unscrew it and pull it out, first cover the floor with rags.

If the items lie at the bottom of the tank, then in this case they are taken out through the opening for the heating element. In different brands of washing machines, the heating element is located either in front or at the back below the tank. When the heating element is located at the back, it is enough to remove only the back cover of the case, then disconnect and pull out the heating element. But with a frontal heating element, read the detailed article, it describes how to get to it.

When the heating element is removed from the seat, shine a flashlight into the tank and find the item. Then, using a homemade wire hook, pull it out of the car.

If the object gets stuck in such a way that the rotation of the drum is jammed, then it is simply impossible to do without disassembling the tank. The process of extracting a foreign object will resemble, which we have repeatedly described in other articles. Getting the tank out is half the battle, if it is non-separable, then in order to remove an object from it, you will have to cut the tank body into two halves. This may take 3-4 hours minimum. The work is not easy and requires skill, so most often it is trusted to the master.

Unpleasant situations with foreign objects in the washing machine can be prevented by being a little more careful and following the recommendations:

firstly, you need to check the pockets of clothes before washing and the reliability of how small parts are sewn on clothes;
secondly, check the contents of the drum before washing and look into the powder cuvettes;
thirdly, clothes with sewn details, zippers, buttons, bones, etc. must be washed in a special bag. And then nothing will get into the tank of the car and will not damage it.

Breaking so simple rules leads to awkward situations. At best, some unnecessary thing will be damaged, at worst, a foreign object will pierce the tank, and then expensive repairs cannot be avoided.

Is it possible to move objects from sleep? Discover the amazing possibilities of lucid dreaming!

The practice of lucid dreaming¹ makes it possible not only to develop internally and learn the facets of your psyche. It is possible to materialize things from a dream into a physical reality!

The reality of this phenomenon has been proven by dreamers. Moving objects from dream to reality is one of the important aspects of the practice of lucid dreaming (or simply LU); a valuable opportunity to model reality at will.

What is needed to move objects from dream to reality?

This is a fairly complex process that can be achieved with regular practice.

Initially, you need to be able to be aware of yourself in a dream, to take events under your control.

The methods described here require large reserves of human energy. Accordingly, in order to increase its level, it is necessary to adjust your lifestyle: follow the diet, the development of the physical body and carry out some meditative practices to increase.

Moving objects from your dreams is possible, but you need to be patient.

Requirements in order to be able to materialize an object into reality:

be in a lucid dream;
have a developed concentration²;
maintain good health so that body problems do not distract from practice.

Moving objects from a dream: technique

There is the following technique for bringing things from dream to reality.

1. The practitioner becomes aware of himself in a dream.

In it, with his intention, he creates an object that he wants to transfer into reality.

2. A person completely concentrates his attention on the subject, presents it in detail: imagines weight, dimensions and details; in one word, all possible properties.

3. After some time, the practitioner remembers his body and begins to focus on it, not forgetting the subject.

4. He brings concentration to the point where both the body and the desired object “merge” for attention, become one.

As soon as such a feeling arises, the practitioner mentally moves into his physical body.

5. The object has already appeared on the subtle plane.

In order for it to appear in material reality, this practice must be repeated for a long time.

However, the stronger the ability to concentrate, the faster the result will come!

It should be noted that the desired item may not appear at home, but somewhere else - for example, in a park or under the balcony of an apartment. It’s just that a feeling will live in you where you need to look for it.

In order to materialize an object at home, you need to clarify this moment in a dream: when the thing you need is created, you need to find your home and transfer this thing there.

Moving items to sleep

There is an amazing way to bring a specific item to sleep! To do this, you need to follow the following steps.

1. The practitioner in reality remembers the object that needs to be moved to sleep. He also remembers the place where this thing is located.

2. A person enters a lucid dream and imagines an object, an exact copy of the real one.

3. When the thing appears in the space of the dream, the practitioner places it in the same place where the original lies in reality.

4. The person imagines an exact copy of the real place and puts the object from the dream in the same place. At the same time, he mentally “destroys” the thing in reality, leaving only the object from the dream.

5. After some time of regular practice, an object from reality appears in a dream. At the same time, he disappears from reality, dematerializes!

For all those who want to learn this practice, it must be emphasized that the result comes with time: it is necessary to patiently continue to practice. He will appear!

homikaze

Notes and feature articles for a deeper understanding of the material

¹ A lucid dream is an altered state of consciousness in which a person is aware that he is dreaming and can, to one degree or another, control its content (Wikipedia).

² Technique for developing concentration

The washing machine is made up of different parts that move and make sounds. But sometimes among them there are incorrect extraneous noises, such as clanging and tapping. If during washing you heard a loud crack or rattle inside the tank, then most likely a bone from a bra got into the drum of the washing machine.

Frame bone for a bra: what is it made of and what harm does it do

At first glance, if you compare the size of the machine and linen accessories, it will seem that it is unlikely to be able to harm. But it's not the size, but the material from which the bone is made.

Most often, frames or bones for linen are made of metal or coated steel.

Getting stuck in the tank of the machine, such corset parts begin to rust, stain water and washable items, and can tear clothes. And that's the lightest of the troubles. Much worse is that a sharp metal bone can easily pierce the tank of the washing machine, damage the coating of the heating element, break the cuff or drain pipe.

If the fittings are made of plastic, then it is less destructive.

Although, when the plastic bone fell deep into the washing machine, she can do things too. For example, pierce the same drain pipe or slip into the pump and disable it.

Where to look for a bone from a bra

An uninvited guest, getting into the washer, falls through and gets stuck in different places:

in drum perforation;
at the bottom of the tank (the most common case): under the heating element or between the bends of the heater tube;
in the space between the drum and the tank (top, side, rear);
in the drain pipe, filter or pump (very rarely).

Depending on the place where the bone from the bra ended up, you can get it in five ways.

Attention! Before you start dismantling the washing machine, disconnect it from the mains! Follow the safety precautions, this will save you from injury and electric shock.

The first way is how to remove the bone from the washing machine through the drum

It can be used if the bone has just begun to fall through and sticks out with its tip out of the perforation of the drum.

To find the part, examine the drum from the inside over the entire surface with your hand. It is very difficult to discern fine fittings in shiny metal, but it is easily detected by touch.

Hook the tip of the bone with tweezers, narrow-nosed pliers or wire and pull it out.

The second way - we take out the bone through the heating element

Attention! This method is suitable for horizontal washing machines with a rear heating element, when the heat element is located below the tank.

You felt the drum and found nothing sticking out. This means that the accessories that “escaped” from the linen have already slipped into the tank. From the experience of repair, the craftsmen know that when the bone from the bra falls into the washing machine, then most often, it falls to the bottom of the tank and gets stuck in the TEN area. And you can get it by pulling the heating element out of the washer tank. In fact, you need to remove the heating element, find and pull out the bone, and then put the heater back in place.

For this:

Remove the back cover from the machine.
Turn off the power to the heating element, remove the terminals from the contacts. Usually three wires are suitable for the heater: phase, zero and ground. Phase and zero have a terminal contact, grounding can be fixed with a nut on the central stud.
Loosen the fixing nut on the stud. You will see it when you remove the ground. Loosen the nut so that it lines up with the end of the stud (you don't need to remove it at all).
Gently press the stud inside the heating element so that it “drowns” to the nut.
Move the heating element and remove it from the nest (sometimes you need to make serious efforts).

Attention! Do not swing the heating element by the contacts or pry with a screwdriver. You will damage the contact pins or the sealing collar.

In half the cases, the bone is removed along with the heating element, because it gets stuck in the loop of the heater tube. In other cases, it is found at the bottom of the tank under the installation site. Often, instead of one fitting, there are two, or even three.

Housewives do not always associate the loss of the frame from the cup with the washer, and the bone can slip into the tank without noises and knocks, without showing signs of its presence. Therefore, it is located only when disassembling the heater, for the company with a “noisy girlfriend”.

Inspect the heater carefully for damage. Sometimes a metal strip breaks the heater very hard, literally into pieces.

But more often it leaves small dents or scratches on the tube, which are hardly noticeable. And the owners of the machine put the damaged element in the tank, and then they are forced to carry out a serious repair of equipment due to a heater breakdown, electrical short circuit and other surprises. Therefore, it is more reliable to immediately change even a slightly rumpled heating element.

When the bone is pulled out, and the heater is normal, you can put it in place.

The procedure will be the reverse of disassembly:

Slide the center stud outward by pushing on the inner retaining plate.
Insert the heating element into the hole, gently pressing the cuff.
Screw the fixing nut onto the stud. Do not tighten it all the way, you will pass the seal and it will leak water from the tank. It is better to twist a little looser, and then tighten if necessary if moisture appears in the hole. But, as a rule, the seal seals the tank so well and additional twisting of the nut is not needed.
Connect the power to the heater.
Plug the machine in and run a test wash without replacing the back cover. To check if there is any leakage from the tank through the heater socket.

Attention! Be careful not to touch the inside of the machine with the cover removed while washing.

If everything is in order, there is no leak, fix the lid, having previously disconnected the washer from the mains.

The third way is how to get the bone through the drain pipe

This method can be used if you do not want to remove the heating element or when it is located under the front cover, for example, in Samsung typewriters. Disassembly of such a model causes difficulties for the owners of equipment - it is necessary to remove the cover, cuff, front panel, etc. to get to the heater. Therefore, it is easier to remove the mounting clamp and look into the tank through the pipe.

Procedure for washing machines without leakage protection will be like this:

Lay the washing machine on its side.
We remove the bottom, if there is one: unscrew the fasteners or snap off the latches.
We loosen the fasteners on the pipe (clamp or ring) and remove it from the tank ledge.
We examine the drain hole and the visible part of the heating element and the tank. We take out the bone from the bra. Sometimes it falls out of the pipe itself, but more often you need to look for accessories by shining a light into the hole.

After removing the foreign object from the tank, install the nozzle in place, fix it with a clamp, fix the bottom, turn the machine over to its normal position.

If you are a happy owner of a washing machine with an Aquastop system to protect the body from leaks, then we recommend getting to the drain pipe through the back wall. In this case, of course, it will not be possible to look into the opening of the tank, on which the pipe is put on, you will have to act by touch, but removing the bottom, where Aquastop is installed, is another task, even for the master. After all, you first need to dismantle the leak protection system, and for this you need to disassemble the half-machine.

The described method can help you get a bra bone out of a washing machine with a front heating element without much disassembly, but it does not always work. The drain hole where the pipe is attached is quite narrow. If the bone does not lie directly above it, but strongly to the side, higher or lower, it is difficult to see it and, moreover, to pick it up. In addition, if it is problematic to remove the bottom of the machine (for SMAs with body protection from leaks), then the possibilities of the search operation are reduced even more: it is inconvenient to crawl up to the tank from below, you have to feel for the bone, as far as your fingers can reach, etc.

The fourth way - how to pull out the bone if it is stuck on the top, side or got behind the cross of the tank

There are rare situations when a bone from a bra gets stuck in the tank somewhere on top, on the side, or flies over the crosspiece. Then all the previous extraction methods will not work, and in order to pull it out, you need to disassemble the tank. The device of the tank varies significantly between brands and models. You can find a diagram, but we do not recommend disassembling it yourself if you have never done this.

There are many nuances that only an experienced master knows about. In addition, some machines have a non-separable tank.

Therefore, as an alternative, a method is suitable that allows you to free the stuck fittings and drop them to the bottom of the tank, from where it can be easily reached through the heater or pipe.

What you need to do:

Unscrew the back cover.
Remove the belt from the pulley so that it does not interfere.
Dismantle the tank pulley, to do this, unscrew the fixing bolt and remove the pulley. Then screw the bolt into the hole about half way.
Take a hammer with a rubber cap or an ordinary light one and a wooden chock. Gently tap on the drum shaft so that it shifts slightly relative to the axis.
Rotate the drum with your hand until you hear that the stone has fallen to the bottom of the tank.

Now it can be pulled out in the second or third way.

The fifth way - we take out the bone from the drain system

It happens that the bone safely slips through the tank with the heating element and ends up in the drain system of the machine - in the pipe, filter and even the pump. It is mainly about plastic fittings for women's corsetry. It, unlike metal, is not so rigid and easily breaks in the drum without causing significant harm to the details of the washing machine. That's why it "flies" so far.

Bone in the filter

First, check the filter. It is usually located in the lower left corner in front of the car behind a special hatch.

To clean the filter and possibly remove the pit:

Open hatch. It is fixed with a latch, so you need to press the cover or gently pry it with a screwdriver.
Slip a dry rag under the washing machine near the filter or tilt the CMA back against the wall and place a container so that residual water does not spill onto the floor.
Unscrew the filter and pull it out of the hole.

Inspect the filter and the hole, the bone can be both there and there. At the same time, remove any other small debris that has fallen into the machine. Wipe the filter installation hole and rinse it with running water.

If the bone is found, then everything is in order. If not, look immediately into the pump (in the case when it is right behind the filter in front). You may see a piece of plastic sticking out and be able to get it out.

Bone in the tube

If nothing sticks out of the pump, and the machine drains water normally, then most likely the bone is stuck in the pipe. You can get it from there.

But first you need to replace the filter and close the hatch. Tighten the filter carefully and at the same time tightly so that the machine does not leak when washing.

Bone in the pump

The first sign that the "uninvited guest" was in the pump is that the machine either does not pump water out of the tank, or drains it badly. The pump can make a lot of noise and rattle. This is not good, but if the pump crackles and stops completely, it's even worse. Silence indicates that the engine has burned out and the pump will have to be changed. Therefore, try to deal with the situation while the pump is still alive and making a lot of noise.

To pull out a foreign object you need to get to the pump and open it.

In different brands of washing machines, the pump is located differently. And there are different ways to get to it.

In most cars of the brands Ariston, Ardo, Veko, Indesit, Samsung, Candy, Whirpool, LG, the pump is at the bottom behind the filter. Therefore, you can first inspect the pump through it. For full access, it is best to lay the machine on its side and carry out all operations through the bottom.
In the Electrolux and Zanussi brands, the way to the pump is through the removal of the back panel, because the pump is closer to it.

In the "Germans" (AEG, Bosch, Siemens) the most difficult way. You need to remove the top cover and front panel, as well as pull out the dispenser, remove the fixation of the hatch cuff and disable the door lock.

Attention! We recommend contacting a specialist immediately if you have German technology. Since disassembly and assembly in these brands is complex and requires experience and accuracy. You can damage the machine by doing it yourself

Pump disassembly

The design of the pump is practically the same. To inspect the "insides", you need:

Prepare a container for water or a rag. When you disconnect the pump, water will pour out of it. To prevent the puddle from being on the floor, carry out the disassembly steps over the basin or place a rag.
Disconnect the pump from power. To do this, you will need to unplug the connector.
Remove the screws that secure the pump to the case.
Disconnect the drain hose on one side and the pipe on the other, loosening the clamps.
Disassemble the pump. To do this, you need to unscrew the snail from the body and pull the engine and impeller out of it.

Now inspect the pump from the inside. The bone can be located between the impeller blades or be pressed against the casing. Pull it out and inspect the impeller itself for damage. If there are any, then you will have to change the pump (the impellers are not sold separately). Even with a “live” engine, a pump with a broken impeller will not drain water.

Rarely, but it happens that the bone did not have time to disable the pump, but simply slowed down its rotation. Then you are lucky and after removing the "alien" you can assemble the pump and put it in place.

Check the pump for leaks before assembling the machine completely, plug it in and put it on a quick wash.

Be careful! Do not touch the inside of a working washer that is not fully assembled.

The bone from the bra fell into the washing machine and lies quietly - get it out or leave it there

Sometimes the bone obviously disappeared in the car, the hostess pulled out her bra and noticed. But at the same time, the washing machine does not make noise, does not tear things and works like a clock. What to do in this case, do you need to look for and pull out or leave the “alien” inside?

Theoretically, you can leave it, but the craftsmen find deposits of bones in the machines during disassembly due to other malfunctions. But remember that even the fittings lying quietly in the tank are a foreign object that should not be there.

A metal or plastic bone at the bottom will eventually become overgrown with dirt (fur, dust from clothes, threads), which will smell unpleasant and you will have to think.

In addition, metal lying in a damp place and constantly getting wet during washing / rinsing will begin to rust and stain the water in the tank, and it will contaminate things. Removing rust stains from linen is very difficult, and sometimes even impossible. That is, the damaged item will have to be thrown away.

A plastic bone is also dangerous because when it comes into contact with a heating element, it begins to melt from heating and smell like burning. This, in the end, can lead to a breakdown of the heating element.

Masters recommend! If the bone is stuck inwashing machine, then remove it as soon as possible. For example, after 1-2 washings. Otherwise, you may face big problems due to an extra detail.

What is the danger of getting a bone into the drum

Smell, dirt, rust on clothes, torn things - these are minor troubles, compared to what a bone from a bra that has fallen into the washing machine can do.

We already talked about serious problems when we figured out what kind of object it was - a bone from a bra. Now let's take a closer look at them.

Linen accessories in the washing machine:

Deforms the drum and damages (pierces) the tank. A sharp metal plate breaks the cells of the drum or flies into the tank wall like a bullet, making a hole. As a result, you have to change the tank or even buy a new washing machine.
Destroys the heating element or damages its surface, which leads to breakage heating element. When a metal bone gets stuck with one end in the perforation, and the other end gets on the heating element, it cuts the heater tube like a knife. If the fittings fall into the hinge, it breaks the heat element into pieces. In the end it has to.
Tearing the cuff of the tank and arranges a leak. As a result, you need to glue your own cuff or.
Pierces drain pipe. If the bone gets into the drain hole, it can pierce the rubber pipe with a sharp end. It is difficult and unreliable to seal holes in it, therefore it is impossible and has to be changed.
Damages or disables the pump. Most often, plastic bones slip into the pump, they break quite easily into pieces, falling into the drum. Once in the pump, bone fragments can damage or jam the pump blades. In the case of a “wedge”, the pump will buzz hard, but will not pump water. If the obstacle is not removed in time, the engine of the assembly will burn out and have to.

What to do if another foreign object gets into the washing machine

A bra bone in the washing machine is not the only "intruder". During inspections, the craftsmen find coins (even commemorative ones!), buttons, pins, curtain fittings, Lego parts, bolts, screws, nails and other small things. The size of this "good" is smaller than that of the bone and they are less likely to linger in the perforation of the drum or at the bottom of the tank.

Their favorite habitats are:

Cuff at the door hatch."Crawling small fry" is easily clogged into a crease and stays there.
Drain pipe. In it remains a metal trifle, screws, nails.
Drain filter. There may be a warehouse of coins, and nuts with screws, and plastic small things. Everything that slipped through the pipe, but did not have time or could not fly into the pump.

Water pump. Light plastic parts are brought there, such as parts of a children's designer, matches, small accessories, buttons.
Drain hose. Matches, small pins, plastic dowels fly there through the pump.

Since the dimensions of this "good" are small, they usually do not cause significant harm, such as a breakdown of the heating element or damage to the tank. But, for example, a nail or a self-tapping screw is quite capable of damaging the heating tube and turning the perforation of the drum, or even making a hole in the tank. And it's easy to break the pump or make a blockage.

Therefore, with extraneous noise in the typewriter, the crackle of the pump and other strange sounds it is worth looking to see if there are any extraneous "guests" in the insides of the washer. If it is difficult to handle it yourself, call a repair specialist.

Professional service of washing machines in Moscow and the region

The RemBytTekh company offers repair and maintenance of washing machines at home in Moscow and the Moscow region. Masters know how to quickly get a bone out of a washing machine Bosch, LG, Samsung, Indesit, Ardo, Electrolux and others. You can see how much it costs to pull out a bone or other foreign object from your brand of typewriter in the table.

Washing machine brand	How much does it cost to remove a foreign object* (only work)
Bosch	from 1500 rub.
Indesit	from 1400 rub.
Samsung	from 1900 rub.
LG	from 1900 rub.
Ariston	from 1500 rub.
Candy	from 1700 rub.
Electrolux	from 1500 rub.
Zanussi	from 1500 rub.
Miele	from 2300 rub.
Whirlpool	from 1500 rub.
BEKO	from 1700 rub.
Siemens	from 2000 rub.
Ardo	from 1800 rub.
AEG	from 1500 rub.
Brandt	from 1800 rub.
Atlant	from 1500 rub.
Gorenje	from 2000 rub.
Hotpoint Ariston	from 1800 rub.
Other brand	from 1300 rub.

* The cost of the work of the master to remove the foreign object is indicated, without taking into account the price of spare parts and work on their replacement, which may be required if damage to the machine is found during the inspection. The price of the service and parts depends on the brand of CMA.

Call "RemBytTekh" by phone:

Or arrange. The specialist will arrive within a day, on the day of the call or the next, at a convenient time for you.

We have been servicing washing machines since 2003! Trust the technique to experienced professionals.