How to attach pvc panels to a brick wall. Methods for attaching plastic panels to the wall. They are assembled in several stages.

If you have started to make repairs in the bathroom or on the loggia, but do not know how to install plastic panels on the wall, you need to thoroughly understand this issue. Learn the intricacies and nuances of this process so that home renovation is only a joy and does not bring unnecessary trouble. The cost of such an interior is many times lower, and the design options are countless.

What are plastic panels attached to?

Plastic sheathing is a great way to solve several problems at once: the parts are easy to mount on the wall, they do not require much maintenance. However, for the implementation of the task, it is important to know how to fix the plastic panels to the wall correctly. Here are the important points regarding the installation of such a skin:

PVC panels can be fastened to the wall using nails, self-tapping screws or using a special liquid nails adhesive.
If the walls are even, then you can mount fasteners directly to them: in the case of a wooden or soft surface, self-tapping screws are suitable, and for concrete, you need to take dowel-nails.
If the walls are difficult to level, a special wooden or metal lattice-frame is installed first.

Each mounting method has its own nuances:

If nails are used, then it will not be possible to remove the plates in order to use them elsewhere: during dismantling, the parts will simply break into several pieces.
Clamps or staples driven in with a special stapler are best suited.

How to fix PVC panels on the wall

To understand how to fix plastic panels to the wall, remember a few useful tips:

Cut the elements themselves, putting them face up.
To protect your eyes, be sure to wear goggles when cutting parts.
When driving nails, it is important to hit the nail head clearly, otherwise dents will remain. It will be impossible to correct such a defect.
Before the end of the installation process, do not remove the protective film, so as not to leave dirty marks on the skin.
After installation, wash the walls only with soapy water so as not to spoil the design or pattern.

On a wooden crate

The question of how to fix the plastic panels on the wall will help to solve the crate made of wood. Reiki must be screwed with a distance of about fifty centimeters. Wooden beams should be perpendicular to the PVC direction: if the details of the future interior are vertical, then wooden structure it is best to nail horizontally.

Install the hardware first. Fix on the surface first the outer and inner corners, then the final element - the ceiling plinth, and at the end - the molding with lamellas.
Next, install the first part connecting the fasteners. Fix with nails or staples on the side of the wide mounting shelf.
So that the whole structure does not turn out to be a curve, before attaching the next part, check the first one. She must stand upright.
Mount the narrow shelf of the second element to the first, leaving no gaps.
So sequentially attach all PVC panels. Only the very last element differs: it must be inserted with force in order to fix the entire structure. If the size does not match the remaining space, cut the part with a knife along the skin.

With a metal frame

If there is always high humidity in the room, for example, in a sauna or a bathroom, then the tree will quickly swell, and you will have to redo the repair. How to attach the plastic panels to the wall in this case? Suitable metal mounting structures. To simplify the process of installing the cladding, special clips are used. Thanks to them, you can easily remove interior elements and attach others.

When installing the skin, remember that the material may expand as the temperature changes. When using a wide beam, sound insulation or insulation can be attached to the free space. So simple plastic panels will help solve several problems at once: create an interior with taste and keep the heat inside the room.

Installation of PVC panels without crates on liquid nails

For flat walls, use building glue, but during such repairs, wear a respirator and ventilate the room. The benefits will cover all temporary inconveniences. "Liquid nails" do not affect the plastic, dry quickly, which gives the right to adjust the details on the wall. Such glue is environmentally friendly and does not depend on changes in climatic conditions (changes in temperature and humidity).

Before gluing the panels, it is necessary to prepare the walls: remove old wallpaper, tiles and plaster, smooth out all inaccuracies and prime the surface.
At the very beginning, remove the boards from the packaging for thirty minutes to allow adaptation to the humidity in the air.
Prepare the glue itself: cut off the tip, put on the cap, open it and install the product in the construction gun.
Draw dots, a grid, or a zigzag pattern on the wall.
At the time of gluing, press the part against the wall so that the glue grabs evenly with the entire element. You can use a rubber roller. The first couple of minutes it is easy to adjust the position of the structure, and after 20 minutes the glue will set.
The final step is to “sew up” the seams between the PVC parts and other elements of the bathroom with sealant. The wall profile is ready.

Video

Even a novice in repair can handle the installation of fasteners and cladding in the bathroom on the wall surface. However, to avoid violations of technology and damage to the cladding, look step by step instructions in the video below, where the specialist will share his secrets in installing sheets and fasteners in the slab and on the ceiling. The guide will help you to install panels flawlessly the first time.

Installation of plastic panels on the wall in the bathroom

How to fix wall panels on the loggia

How to fix plastic panels - step by step instructions

Thinking about the repair, we always want to get an excellent result, and at the same time do without extra costs and meet the minimum deadlines. Another important point- to repair work they did not cause much trouble, did not leave behind dirt and did not interfere with neighbors much.

An excellent solution in this case would be the installation of plastic panels. Our instructions will help you understand how to fix plastic panels. They are easily mounted on walls or ceilings and do not need to pre-level the surface.

Plastic panels are easy to clean and ideal for rooms with high humidity(bathroom, sauna, boiler room). A variety of colors and textures will help create a unique and cozy interior. For the installation of such panels, it is enough to have several tools at hand.

Necessary tool and preliminary preparation

The tools necessary for fixing plastic panels can be found in almost every home:

electric drill;
wood saw;
scissors and a hacksaw for metal;
screwdriver or screwdriver;
tape measure, building level, pencil or marker;
hammer, stapler;
ladder.

First, use a tape measure to measure work surface, this will allow you to correctly calculate the required amount of materials.

The surface must be freed from wallpaper. If the panels are glued, be sure to clean the walls or tiles from paint and dust.

Installation features and procedure

The panels are fastened either directly to the wall or to a crate prepared in advance. To mount on the wall, it must be perfectly flat. The crate is wooden bars or rails that are screwed to the surface at a certain distance from each other. For walls, the width between the rails should not exceed 30 - 40 cm, for the ceiling - no more than 30 cm. The rails for the crate are attached to the wall perpendicular to the direction of the panels.

If the wall to which the rails are attached is wooden or any other wall into which self-tapping screws are easily screwed, then it is best to use them to fasten the bars. If the wall is concrete or brick, then it is best to fasten the bars with dowel-nails or with ordinary dowels and self-tapping screws.

An example of fastening a crate for plastic panels.

Before you get started, you need to understand how to properly attach the plastic panels to the wall.

If you decide to fasten the panels to the crate with nails, then keep in mind that the reuse of the material will be impossible, since, most likely, the integrity of the panel will be violated during dismantling.
The best method of fastening is with clamps.
But the use of staples that are driven in with a special stapler is also a good option.
Another good option for fastening panels is self-tapping screws.

The most common ways of fastening plastic panels.

After you have decided on the method of fastening the panels, you need to do the following:

First, install the fittings: the final element, the outer or inner corner. If the panel closes the wall to the ceiling, then fix the ceiling plinth to the top beam.

Available types of fittings for plastic panels.

Insert the panel into the fixing element with a narrow fixing flange. The panel is fixed from the side of the wide mounting shelf with nails or brackets.

After making sure that the first panel is level, insert the next one with the narrow end into the groove of the previous panel. Try to mount panels closely to each other.

Installation of the necessary fittings and the first plastic panel.

The last plastic panel that completes the row must be inserted with force between the final element and the previous panel. If the panel needs to be reduced in width, then cut off the excess with a knife, moving along the panel.

Video: Installation of battens, fittings and PVC panels

Features of mounting plastic panels on walls

If the room is dry and the walls are even, then the panels can be mounted directly on the wall without using the crate.

Fastening panels with glue directly to the walls without using a crate.

In a room with high humidity, a plastic or metal mounting profile should be used as a crate. In this case, the panels are attached to the rails with special clips, which greatly facilitates the installation and dismantling of the structure.

Fastening panels using a plastic profile using special clips.

Consideration should be given to the expansion of the material with temperature changes, so when adjusting the height of the panels, leave a small gap. If a wide beam is used for the crate, then a heater or soundproofing material can be placed in the resulting space between the wall and the panels.

Features of mounting plastic panels on the ceiling

Now consider how to attach plastic panels to the ceiling. Before installation, it is necessary to determine the distance between the panels and the ceiling. This gap will depend on the type of lighting. If you plan to install recessed lights, then the distance should be at least 10-15 cm, so you can completely hide the wiring. Mark in advance with a pencil the places of the lamps, cut out the holes and install the bases of the lighting devices.

Metal crate for mounting plastic panels on the ceiling in the bathroom.

Next, you follow the same steps as when mounting the panels on the walls. In a room with a flat ceiling, you can do without crates. Ceiling plinth before starting work, install on three walls. Use a building level to evenly place the panels.

When installing plastic panels in a room with high humidity, fill in the ceiling gaps silicone sealant for complete waterproofing.

1. Cut and drill panels face up. For cutting, use a hacksaw, a hand saw or a construction knife. Always wear goggles to protect your eyes.

2. Apply glue directly to the wall. Draw a grid with even lines, leaving no empty areas. Use only special building glue "liquid nails".

3. When driving nails into the panel during installation, be careful not to hit the surface with a hammer, otherwise dents will remain.

4. Clean plastic panels with soapy water. Do not use abrasive cleaners, scouring pads or solvent-based cleaners.

Now you know how to fix plastic panels to the wall and how to care for them. Installing plastic panels does not require much time and is within the power of any beginner. By choosing this easy-to-install material, you can create a unique interior with your own hands. Among the variety of panels that imitate stone, wood, paper of various colors, you are sure to find an option to your liking.

Be sure to watch the video below, it very clearly shows the process of installing plastic panels.

Video: Finishing the walls and ceiling of the bathroom with PVC panels

How to fix plastic panels to the wall

If you decide to finish the walls and ceiling in the bathroom, hallway, kitchen or balcony, then you should look for materials that can cope with high humidity in these rooms and do not change their properties. And PVC panels will be the best option in this case.

They are not expensive, practical and of high quality. Among other advantages, the panels are easy to clean, do not deform from contact with moisture and do not fade in the sun. Yes, and installation is quite simple.

They are just perfect for leveling walls, and thanks to a wide color palette, they allow you to realize any designer fantasies. But the fastening of the panels has its own nuances and subtleties.

Materials and tools

Installing plastic panels is quite easy, and therefore you can do this work yourself. But to do the work yourself, you need some simple tools:

After all right tool prepared, you can go for panels, materials for crates and fasteners. But it's still worth it first. to do everything necessary measurements so as not to buy too many materials or, conversely, not to buy them later.

How to calculate materials

Plastic panels are available in a variety of colors and sizes. The length of the panels most often varies from 2.7 m to six meters, while their width can reach 50 cm, and the thickness of the panels - 8 or 10 mm. Based on these parameters, you should calculate the required amount of materials for finishing rooms.

First you need completely measure the room without missing a single wall, then you need to decide in which direction the panels will be laid - along or across. And already at the end of all measurements, the amount of material needed should be calculated.

It is worth remembering that from how you will fasten the panels - along or across, you can visually resize and outlines of the room. If the panels are placed parallel to the floor, then the room will visually appear wider, and vertically higher.

In order to complete the crate, you will need metal profiles or wooden bars . Installation of plastic panels on the wall is carried out by mounting on the frame or installing on liquid nails and glue.

Fastening plastic panels to the wall on the frame

Before you start finishing the walls, you need to make a frame from a bar or a metal profile. Before starting work, you need to remove excess dirt and dust from the walls, and also treat the surface with a special antifungal agent.

Then you need draw a grid using a level. The distance between the rails should be no more than 40 cm. On the marking lines, holes must be drilled at a distance of 50 cm from each other. It is in them that the profile will be attached to the wall with suitable fasteners.

First you need to fasten those profiles that will go along the perimeter of the room, and only then you need to fix the transverse parts.

If the walls in the room are relatively even, that is, the difference is not more than 5 cm, then it can be used for the frame wooden bars, but with a larger difference, you need to use a metal profile. It is much easier to fix it at a distance from the wall using special fasteners. After the crate is completely completed, you can proceed to the finishing work.

It is worth starting work from the corner farthest to the entrance, because it is he who is best viewed and any trimming will be visible here. To get started you need fix the starting strips top and bottom of the frame. Attach the outer or inner mounting angle to the side. These elements will help to fix the plastic and hide the external unaesthetic appearance of the panel cuts. Now you can start installing the material.

Cut the plastic to the desired size, it is better to make it 5 cm less in height - when changing temperatures, this will help the panel not to deform. Insert it first into the upper and lower groove, and then into the side. Plastic must be fixed in each rack of the crate fixing with screws or stapler. Subsequent strips will be attached in the same way.

Installing the last strip is the most difficult step. To do this, it needs to be cut half a centimeter less than required by the rules. First insert it into the corner profile, and then snap into the groove of the previous panel. Thus, you do not deform the guides and neatly finish mounting the wall.

Installing PVC panels with glue and liquid nails

Perfectly flat walls are a rarity these days. But if you are a happy owner of such walls, then there is the possibility of installing panels without the use of crates. This method has a lot of advantages, but there are practically no disadvantages:

But first you need to be as thorough as possible prepare walls for work. All visible dirt must be removed from them, primed and smeared with an antifungal compound. Now you can attach the plastic.

If the wall allows, then the panel should fasten with a self-tapping screw somewhere in the middle of the wall, this will help provide a more secure fit. In the corners of the room, a special flexible corner should be glued. It helps to hide the curvature of the corners, give the room completeness and forms the inner and outer corners.

But it should be remembered that with this method of installation it is impossible to hide the wiring and fix the lamps. Therefore, the choice of method is up to you.

Installation of PVC panels on the ceiling

Installing PVC panels on walls is much easier than on the ceiling, but you can do it yourself with your own hands. After all, the PVC panel helps to hide the wiring, communication pipes, ceiling irregularities. And they are also convenient to place spotlights on.

Ideal for ceiling frame made of metal profiles, which will help to attach the PVC plate more securely. In addition, the metal frame is not deformed by moisture and temperature changes.

Before proceeding with the assembly of the frame, you need to carefully prepare the ceiling. Remains of paint, whitewash or plaster must be removed from it. Then you need to treat the surface with an antifungal compound.

To start need to markup walls at a distance of 10 cm from the ceiling. After that, you need to install the elements at a distance of 40 cm from each other. If the distance is longer, then the PVC tracks will sag over time.

Then you need fix start profile or a special baguette for plastic. Corners should be cut using a miter box. But you can cut the corners with the help of a clerical knife already at the installation site. After that, the panels can be installed.

At the end of the work should be installed around the perimeter of the room plastic molding, and on the floor to let plastic plinth. On this, all the work on finishing the room with plastic is completed. If the panels are carefully exploited, they do not lose their attractiveness and beauty for a long time. And given that it can be easily washed, this finish becomes a real find in rooms where you often have to wash walls and ceilings.

Just do not use aggressive products to wash the panels - they can destroy the surface and you will have to change the cover. But this also has a significant plus - if one track is damaged, the entire surface does not need to be changed, it is enough to remove the damaged area and replace it with a new one.

As you can see, you can easily decorate walls and ceilings with PVC panels with your own hands. All work is carried out in stages. And if strictly follow the instructions of professionals, then the work can be done in the shortest possible time and without much effort. But remember that the materials you need to select are of high quality and reliable, and it is better to take a professional tool.

How to fix plastic PVC panels on the wall yourself

PVC panels are one of the the best varieties finishing and decorating ceilings and walls in different rooms, especially places with high humidity, which include kitchens, balconies, hallways, bathrooms. They attract both their cost and quality indicators and convenience.

Mounting methods

There are three methods for attaching PVC panels to the wall - self-tapping screws, kleimers, glue. Fastening with glue is only suitable for perfectly flat walls. Before use, you need to level, clean and dry the surface for fastening. After that, a uniform amount of glue is applied to the material, and it is fixed to the wall.

Types of glue for mounting PVC panels:

special adhesive mixture for PVC panels;
universal glue "Moment-mounting";
liquid nails.

For gluing, you can use the frame. Thanks to him, there is no need to level the surface of the walls, and the adhesive composition is applied to the crate from the tree. It is strictly contraindicated to use adhesive material with components such as a cleaner or solvent.

Fastening with self-tapping screws is one of the win-win ways of fixing plastic, which does not require leveling the surface to a perfectly even state. So that the work does not drag on for a long time, you will need a screwdriver to screw in the screws. The disadvantage of this method of fastening: a more suitable frame in this case is wooden, so it will take more time to saw the timber and treat it with an antiseptic.

Most the best way- this is a fastening with clamps. They are easy and quick to mount in the crate. Kleimers contribute to the reliable fixation of the material on the wall. The crate is easily assembled from a metal profile. In case of damage to the lining, it is easy to change it for a new one. Finishing installation is done quickly.

Fastening tools

Before proceeding with the installation, you need to prepare a set of tools. Most of them can be found in the home of every owner. Required to work:

for marking - a pencil with a tape measure;
a hacksaw with fine teeth to cut the canvas;
construction level;
plastic profile or rails for fixing;
perforator, screwdriver;
antiseptic, sealant, adhesive composition.

Before you start finishing the walls with clapboard, you will need to remove the old coating, check for cracks, if there are any, eliminate them, and treat the surface with a fungus agent. When mounted on a frame, you can do without additional leveling of the surface.

Installation sequence

PVC lining can be fixed directly to the wall or you can use the previously prepared crate for attachment. It is made of slats or beams of wood. For attaching to the wall, the distance between the bars is no more than 300-400 mm, for the ceiling - 300 mm.

Before proceeding to the beginning of fastening, it is better to thoroughly understand how to properly fasten plastic panels. When PVC products are nailed to the crate with nails, there is a high probability of breaking the integrity of the material, which will make it impossible to reuse them, so it is better to take clamps, staples or self-tapping screws.

Then fittings are installed: the final part, a corner on the outside or inside. A ceiling plinth must be attached to the top rail if the wall is closed with clapboard up to the ceiling. The material is inserted into the fastening part with a thin fastening shelf and fastened with nails or staples to the side of the wide mounting shelf. When the lining is evenly attached, the next one is inserted into its hole with the narrow side. Panels need to be fixed closely, one to the other. The lining that completes the row must be properly fixed between the final part and the panel preceding it.

In a dry room with even walls, it is not necessary to use a crate, and the lining can be fixed directly to the wall. In case of high humidity, instead of a crate, it is better to use a profile for mounting from plastic or metal. Clips are used for fastening, which greatly facilitates the work with panels.

When attaching the lining to the ceiling, it is necessary to determine the gap between it and the ceiling, which will depend on the type of lighting available. To hide the wiring with built-in lamps, this gap should be 100-1 50 mm. Before fixing the panels, holes are cut out for chandeliers, socles of lighting devices are installed in them. Then the PVC panel is fixed to the ceiling in the same way as on the wall..

With a flat ceiling, it is not necessary to use a crate. Getting started, a ceiling plinth is installed on three walls. For even placement, a building level is used. Before fixing the lining in rooms with high humidity, gaps and cracks in the ceiling are filled with silicone sealant to create a water tightness.

Getting started, you need to know how to fix the PVC panels correctly and attach the material securely. Do not neglect the technical guidance and recommendations of professionals that can facilitate the installation.

During cutting and drilling, the panel must be face up. Cut better with a saw for metal products or manual, construction knife.
The adhesive composition is applied in straight lines to the wall, drawing a grid.
For the cleaning wall panels it is better to use soapy water. Do not use solvent detergents, which include abrasives, coarse washcloths.
Before attaching the plastic panels to the wall, it is recommended to wear protective goggles.
Before starting work, familiarize yourself with the theory of how to attach plastic panels to the wall.

Performing the work step by step and following the instructions, you can do the installation of the panels yourself, without resorting to the help of masters.

Installation of decorative panels allows you to solve many urgent problems. And it's not just about the design of the rooms as such, of course. But just buying the right products is not enough; you still need to carefully study their features and understand how to mount them correctly.

Criterias of choice

Speaking about plastic (PVC) decorative sheet materials, about their installation, one cannot get around the question of what exactly is to be mounted. Even the most scrupulous adherence to technology will not allow you to achieve a good result when using bad products. Most wall panels are purchased for bathrooms, because great importance It is resistant to moisture and microbial attack. Since any wall periodically experiences mechanical stress, the surface must be resistant to such a development of events.

First of all, it depends on the thickness of the outer surface. Reliable wall blocks should have a layer of 0.25 cm, while in the ultra-budget category this figure reaches only 0.15 cm (if it still does). Also important appearance: a good product is always even, not only in its own geometry, but also in color.

Strength is determined not only by the depth of the panel, but also by the number of ribs. The most reliable designs are equipped with 29 such parts, and the average is 20. But the edge is different, they must also be perfectly smooth and not differ in thickness; any placement other than at right angles to the surface is prohibited.

It is also useful to look at the joints of the panels, which should be joined as tightly as possible. Since thick walls and extra ribs cannot be created out of thin air, a good block is quite heavy. It can even be considered one of the practical advantages. Another circumstance should be taken into account: you can finish the walls in the house either well or cheaply. Experienced owners always purchase at least panels of the middle price group, and qualified builders approve of this.

In addition to these obvious considerations, it is worth paying attention to the chalk, or rather, its concentration. Compliant panels contain this mineral only in trace amounts. When deflected by half, they will straighten out, and there will be no dents on the surface. But even flawless wall blocks can be damaged by improper operation.

Preparatory stage

Doing everything right will not work if you do not prepare for installation. Scrupulous work is not required, but accurate measurements of the surfaces to be finished and the calculation of the required volume of material are extremely important. At the preliminary stage, they decide how to mount the panels. Ideally smooth surfaces that only need to be decorated are simply pasted over. And if there are deviations from strict verticals, then you will already need to create frames; they will also have to be used to mask communications.

Initially, the lowest point on the ceiling is found, from which marks are equal in width to one panel. With a level around the entire perimeter, marks are made where anchors or dowels are to be fixed. These fasteners will help attach the frame to the walls.

The profiles should be attached at an angle of 90 degrees to the plates to be placed on them. You can make installation easier if you add a thin cord to the marking and checking the level, the edges of which are covered with colored chalk and pressed against the surface to be treated.

The profile itself can be formed both from wood and from metal and even from plastic. Choice suitable material determined primarily by the conditions in which it will be used. So, wood shows itself well in a “regular” room, but its prospects are much worse in bathrooms or on open balconies. And even where high humidity is unlikely to occur, you will have to use specially selected impregnation. This is the only way to exclude the effect of liquid and the occurrence of mold foci.

Tools and accessories

For work you will need:

stepladder (more convenient than a movable table or stool);
drill (replaced by a puncher);
roulette;
hydraulic level;
saw for metal;
painting knife;
self-tapping screws;
a hammer.

In addition to additional tools, it is worth noting the value of prepared accessories. You will definitely need the so-called starting profile, which helps to close the borders of the panels at the ends. In addition to it, you will need an F-shaped profile, which provides the best decorative qualities of the end blocks. Specialized moldings help to connect various panels into a single structure. Its own type of profile exists for external and internal corners.

Since the panels will be adjacent to floors and ceilings, two types of skirting boards are required. Useful soft universal corners. Fastening to the frame parts is provided with self-tapping screws or galvanized nails. All components, with the exception of the frame rails, which are not visible from the outside, must have the same color as the panels. Even experienced designers do not recommend experimenting with color contrasts in this case.

Calculation

In order for the wall surfaces to be finished properly, it is necessary to carefully and scrupulously calculate the need for the blocks used, in the components for them.

The standard dimensions of wall panels are:

in thickness 0.6-1 cm;
in width 25-30 cm;
length 250-600 cm.

The key value, according to professionals, belongs precisely to the width. If you choose the largest products, it is possible to reduce the number of seams, and the appearance of the installation will be closer to the integral surface. But during the work itself, narrow structures are more practical, because they are easier to bend. And the relative lightness of each block makes itself felt.

A compromise is reached when using panels with a width of 250 mm.

The calculation itself begins with determining the perimeter of the sheathed base. From this figure, the perimeter of each door, each window or other part that for some reason cannot be sheathed is subtracted. The result obtained is divided by the perimeter of a single block (only remembering that part of the material of the blocks will go into segments). Rounding in calculations is always carried out upwards, and the margin for cuts is provided in the amount of 10%. If there is no experience, you can even leave 12-14%.

slats will have to be placed not only on the edges of the walls, they need to surround the openings of doors and windows;
the standard profile gap is 0.3 m;
the very first profile is always rotated at right angles to the future mounting plane;
the rails themselves are fastened to the walls with self-tapping screws or dowels with a gap of 400 mm;
the guides are attached to the rails at a distance of 500 mm.

Mounting methods

On the frame

When all the PVC panels are selected and purchased, when the components for laying are prepared, you can proceed to it immediately. And in many cases, the most practical solution is to use a framework. Fasten with screws decorative blocks even on relatively uneven surfaces. But there is a problem - you will either have to use a screwdriver, or spend a lot of time. To screw in the screws, it is advisable to use a crate made of wood, therefore, first they saw the timber and impregnate it with antiseptic mixtures.

Alternatively, you can mount the panels with your own hands using clamps. Such details provide reliable retention of decorative blocks. When using kleimers, the crate is formed from metal, and the coating can be assembled without additional effort. Each deformed block is quickly replaced with a new product, and even if the entire lining ceases to suit, it can be easily changed. The installation of frames is carried out exclusively by levels so that there are no distortions.

It is not necessary to measure each individual rail, you only need to mark the walls. The lowest course of the frame is created 10-20 mm above the floor. From the selected point, draw a line using a level. Similarly, show features under the ceilings or along the edges of the finish. Then, 400 - 500 mm recede upwards from the lowest strip that needs to be sheathed, set up a beacon, and so systematically move to the upper strip; beacons will help ensure the parallelism of the lines.

It is important to note that horizontal frames should be mounted in vertical plane, vertical - horizontally. If you need to hang the panels on uneven walls, the crate is mounted on top of wooden wedges. The wires running along the walls are hidden under the finish.

Since you can’t joke with electricity, all work is carried out only after measurements. Clamps press the wiring so that it does not protrude beyond the boundaries of the crate.

Lamels are placed, moving from the most distant (with respect to the entrance) corners. But if for some reason another place is most noticeable, they work from there anyway. The panel is fastened by inserting it into the side moldings, attaching it to the corner and attaching it to the crate from the reverse side. The next block is inserted into a special groove on the first one, the joints are thoroughly pressed and attached to the frame rails. You can increase the tightness of the joints by lubricating the sidewalls with silicone.

The following panels are connected in exactly the same way. To prepare holes for sockets or switches, sharpened knives are used. When the installation is completed, the treated areas are covered with plastic boxes. But to insert the last lamella, it is cut in width. Preliminary fitting is carried out on the wall, basting with a pencil, after which they take a hacksaw.

Each corner, each connection should be covered with moldings. With their help, the panels are inserted with edges on both sides, and all intersections immediately become more pleasant to look at. The final stage of work is the installation of a decorative molding along the entire perimeter of the ceiling and a plinth repeating it at the bottom. If you operate the panels installed in this way carefully, they will retain their attractive appearance for a long time and will not require repair.

Before starting work, be sure to:

remove loose coatings;
looking for cracks and chips;
if they are found, they immediately putty or plaster problem areas.

An additional difficulty is the installation of PVC panels in rooms exposed to moisture. The primary surface must be covered with waterproofing. It is applied to a pre-moistened base. When the product dries, it is treated against mold fungi. When timber battens are used, all calculations of distances from the wall must allow for an allowance of 0.2 - 0.3 cm for possible deviations from the ideal shape.

The upper and lower levels are adjusted according to the hydraulic level, and the side lines - according to the plumb line. Fastening is carried out through suspensions that set the indent. After mounting the battens, carefully check whether its outer edges are on the same line. Adjustment, if necessary, is carried out either by reducing the beam with a planer, or by adding substrates. If screws are used to create the frame, the gap between them will be from 200 to 250 mm for wood and from 150 to 250 mm for metal products.

frameless

Fastening PVC panels does not necessarily mean the use of frames. Often the installation is done with glue. The procedure itself is simple, you just have to carefully prepare for it. Naturally, it is required to remove all the previous coating completely and close up the cracks. If with the framework technique the remaining integral layer could be tolerated, then here the situation is already different.

Making a perfectly perfect wall is not always possible. But even inexperienced people can reduce the height difference to 5 mm or less. In addition, before attaching the panels to the adhesive, it is required to wash off the whitewash, remove greasy traces with detergents and apply a primer. After all this work, the decisive factor is right choice and application of glue. It is allowed to use universal adhesives, but it is much more correct to choose compounds that are specially made for joining plastics.

Quality adhesive:

forms a transparent film in a frozen form;
immune to getting wet, cooling (even alternating with overheating);
adheres two surfaces in a short time and retains its ability to hold them together for a long time.

Hot melt doesn't work at all. It holds the panel too tightly and does not allow the plastic, which expands rapidly when heated, to move. As a result, he quickly disappears. It is advisable to use sealants based on polyurethane or "liquid nails". They allow you to avoid such an unpleasant development of events.

The panels themselves are rubbed with a damp cloth before gluing on the reverse side. This allows dust to be removed.

Then pointwise, at a distance of 0.25 - 0.35 m, glue is applied. Contrary to the evidence, when using liquid nails, the attached panel must be tapped and removed. Only contact with air for 5 - 7 minutes ensures the stability of the connection during repeated application. Frameless installation almost always dispenses with the creation of external and internal corners.

Use instead of them plastic corners without grooves. Such products are pasted over with transparent silicone, rubbing with a damp cloth that removes excess mixture. The insert can, depending on the severity of the angle, reach 2 - 5 cm. The places where the electrical outlet should be placed are cut out. Turn off the power supply in advance; installation is completed by laying skirting boards at the joints with the floor and ceiling, which are screwed with self-tapping screws.

Panel borders cover mounting foam or silicone sealant. The second option is optimal where the humidity is excessively high. If you have to cut off the glued parts, use hand saws or electric jigsaws. Sometimes frameless installation PVC panels are produced using a construction network.

Sheathing the wall with PVC panels, whether framed or frameless, is carried out only in rooms where there are no temperature fluctuations greater than 20 degrees. It is not allowed to install in a room where the air is colder than +10. If the panels were stored or transported at a lower temperature, they should be kept under normal conditions for at least 48 hours. It is advisable to install a heat-shielding material under the lining. The crate is placed with a maximum step of 0.5 m, no considerations justify exceeding this distance.

Cladding slats should encircle not only openings for windows and doors, but also kitchen vents, as well as ventilation outlets in other rooms. The recommended size of the rails is 3x1 or 3x2 cm. When it is clear that the room will be especially humid, the crate is equipped with cuts. This will improve ventilation. When plastic blocks are connected horizontally on the facades, the grooved edges are oriented downwards in order to prevent the grooves from being filled with water.

Leaving upper and lower gaps of 0.5 cm helps to compensate for temperature shifts. The vertical layout of panels with a pattern is carried out from left to right, from one corner to another. For blocks that are colored monotone or form a pattern that is symmetrical in any direction, the choice of primary angle is subjective. In addition to the tools listed above, work may require victorious drills, screwdrivers, miter boxes, pliers, squares, furniture staplers with staples 1 cm long. When using a finish without seams, maximum attention should be paid to the density of the bow of its parts, otherwise it will turn out ugly.

It is extremely difficult to decorate walls with your own hands using panels decorated with bright and rich patterns, characterized by abundant detailing. Judging by the reviews, such work inevitably causes difficulties, especially when placing components and complementary elements. The relief of the mosaic forces us to completely abandon the idea of removing corner cracks. You should carefully choose the color of the panels to be mounted, because errors of this kind are difficult to correct. The closer to each other the parts of the frame, the stronger it becomes as a whole, but it is impossible to bring the fasteners closer than 300 mm.

It is not advisable to use adhesive fastening if it is known for sure that PVC panels will have to be removed in the future. And the need for this sometimes arises suddenly, so you should definitely think about frame mounting. To attach the cladding to metal profiles, it is recommended to use self-tapping screws with press washers. Irregularities of the concrete wall are corrected by laying a bar of the required thickness. In the hallway, you can use PVC panels without any doubt, you just need to carefully select them.

Most often they stop at imitation of natural wood. Regardless of the reproduced breed and dark or lightened color, a calm and benevolent interior is created. AT contemporary setting use tones such as wenge or bleached oak.

It is worth remembering all the time that in the corridors of a small size, an excess of darkness is contraindicated. Be sure to achieve contrast in the color of the walls and furniture.

More and more popular is the duplication of the appearance of the stone. A variety of PVC coloring with specially selected pigments facilitates this task. Choosing suitable option“stone” wall, we must first ask ourselves whether it is necessary to emphasize the luxury and solidity of the image or to form a laconic ensemble. Regardless of the approach chosen, there is sufficient space to demonstrate originality. It is not even necessary to use the finishing with one panel, they are well combined with other materials (LKM, various wallpapers, frescoes).

Corridors with dim, subdued lighting should be finished with light materials. Otherwise, the space will be visually absorbed. Large rooms can already be covered with large-scale drawings and geometric patterns. If the walls are made light, and flooring- dark, you get an expansion of the room. Attention should be paid to the selection of accessories for PVC panels.

So, the H profile is used at joints and joints, and L is used to start laying and at the ends, although both products are 3 m long and are designed for 0.8 cm panels. P-shaped plastic profiles are inexpensive and weigh a little, make fastening easier. At the same time, they are exceptionally resistant to humidity, water vapor, and temperature fluctuations. You need to install such blocks at intervals of 30 cm. But self-tapping screws or dowels are screwed in every 100 cm.

Profile grooves in the form of the letter P can be used for pulling cables. If the use of a metal crate is chosen, the cable should be pulled in PVC pipes with a corrugated sheath. Only it excludes the destruction of the braids by the cutting parts of the profile. For technical reasons, it is unacceptable to install any PVC blocks in places where a temperature of more than 40 degrees can occur, with or without high humidity. Instead of trimming the final panels in width, you can unfold them, bringing the locks to the opposite side and cutting off the groove from the outside.

All work with PVC must be carried out more carefully than with wood. It is fragile and any sudden movement can create cracks in the outer layer. There is no way to remove them, the panel will be hopelessly damaged.

PVC panels are a popular finishing material that is durable, practical and affordable. Such coatings can be used both for wall cladding and for decorating the ceiling. Plastic panels are installed quite simply and quickly. It is quite possible to cope with such work on your own. Today we will talk in more detail about how to fix PVC panels to the walls.

Advantages and disadvantages

Plastic panels are a popular and common wall covering. They can be found in many stores specializing in the sale of finishing materials.
Wide sheets and plastic lining are in great demand because they have many positive qualities.
First of all, it should be noted the durability of such finishing materials. In our climate, their service life can be more than 20 years.
Such materials are wear resistant. They are not afraid of dampness and moisture. In addition, they are not subject to decay, like, for example, natural wood.
Plastic panels do not require complex and regular maintenance. Dust and dirt do not accumulate on their surface. If the finish is dirty, then it can be cleaned with a regular damp cloth.
PVC panels have soundproofing properties, so they are perfect for wall cladding.

Using plastic panels, you can divide the space into functional areas.
Plastic panels are lightweight materials, which makes them easy to work with. All processes can be handled without the involvement of assistants.
Plastic is a very malleable material - it easily lends itself to various types processing. Therefore, in stores you can find PVC panels that have a variety of colors, textures, prints and ornaments.

These Decoration Materials can be used in interiors of various styles. The only exception can be only fanciful and pompous ensembles, in which only expensive and natural elements should be present.
You can install plastic sheets both in a city apartment and in a private house.
Behind the panels you can hide various communications, for example, electrical wiring.
It is quite possible to install PVC panels on walls with your own hands, since this process is not complicated and inaccessible. You don't need expensive tools to do this.

Of course, PVC wall panels are not ideal finishing materials. They also have their own weaknesses.

Knowing all the advantages and disadvantages of PVC panels, it will be easier to work with them. You can avoid many mistakes during the installation process.

Criterias of choice

PVC sheets produced by various manufacturers have different properties and performance characteristics. When buying a suitable material, you need to pay attention to its quality - this is the main criterion that you should rely on.
there are damages on their stiffeners (even barely noticeable) or they are completely deformed;
stiffeners protrude too much;
if the lines of the pattern on the front half are poorly expressed, and there is also blurring of the edges;

scratches and other minor damage are visible on the surface of the panels;
lamellas from one set differ from each other in hue and brightness (such a finish will look inharmonious and ridiculous on the walls);
panels from one set have different sizes (in this case, the finishing installation technology will be noticeably complicated, since different-sized elements will not be fixed qualitatively).

Pay attention to the decorative layer of the panels. Any drawings, prints and paints should not be blurry or too dull. These features may indicate the low quality of the material. Such coatings will quickly lose their original appearance.

Currently, there are Chinese and Chinese PVC panels in stores. European production. European products are considered to be of better quality.

When choosing a suitable material, it is necessary to pay attention to its density. It depends on this parameter how durable and wear-resistant the panel is. This indicator is affected by the number of rigid edges that are located in the inner part of the sheets.
The optimal indicators are:
thickness of the front side - 2-1.5 mm;
the number of stiffeners - 20-30;
the total weight of the part is 2-1.7 kg / m2.

To make sure the reliability and strength of the material, you should press on it with your finger. The front side of the panel should bend slightly under its pressure, and then quickly return to its original state. If the lamella is strongly deformed, then this indicates that it contains a large number of chalk - such materials do not last long and are very fragile.

Preparatory stage

If you decide to install PVC panels yourself, then you should adhere to a specific work plan. If at each stage you do everything correctly, the result will not disappoint you.
First you need to prepare the wall base for future plastic cladding. This work is especially important if you plan to attach PVC panels in a frameless way.

Work algorithm.
First you need to remove the old finish coatings and any elements that may fall off the wall.
It is also necessary to get rid of all the defects of the floors. If there are noticeable potholes or cracks on their surface, then they should be repaired with a suitable solution.
Too prominent areas need to be cut off.
When the wall is leveled, and all the shortcomings are eliminated, it must be treated with a high-quality primer with antibacterial components. Such coatings are necessary so that the base is protected from the formation of mold or fungus.

Only after all the work done on the preparation of the walls, you can proceed to the design of the crate (if you use the frame method of installing the material).

Tools and accessories

For the installation of PVC panels, it is necessary to properly prepare and stock up on all necessary tools and accessories.
You will need these tools:
tape measure with a pencil or marker (indelible) to mark;
a hacksaw with small teeth for cutting sheet panels;
building level and plumb line, so as not to encounter distortions and irregularities;
triangle;
plastic profile, slats for decorating the corners of the structure;

self-tapping screws, dowel-nails, kleimers for fixing various elements on the base;
screwdriver and perforator;
sealing composition;
glue;
antiseptic.

Also in the process you will need special accessories:
external and internal corners;
docking profiles;
starting profiles;
F-shaped profiles;
ceiling and floor plinths.

All tools and accessories must be of high quality and reliable.

Calculation

It is recommended to proceed to finishing work only after all necessary calculations have been made. This stage is needed to find out the exact number of PVC panels that you will need for wall cladding. Thanks to accurate calculations, you can avoid unnecessary overpayments due to the purchase of material with a large margin.

Fixing PVC sheets involves their horizontal or vertical arrangement. In this case, the choice remains only with the owners.

first you need to measure the entire room (that is, find out the length along the perimeter);
then you should subtract the width of window and door openings;
now the remainder must be divided by the width of one PVC panel.

As a result of such simple calculations, you will get the number of panels needed to finish the room. It is recommended to add a couple of additional units to the resulting value. This is necessary so that you have a spare in case of damage to some parts.

As for the calculation of the amount of material horizontally, it is carried out as follows:
first you need to measure the area of \u200b\u200bthe room;
then the area of door and window openings should be subtracted from it;
the resulting number must be divided by the area of \u200b\u200bone panel from the kit.

Add 10% to the final figure - this will be a reserve. It should be borne in mind that when laying out horizontally, plastic panels will have to be cut, so you will have leftovers in the form of PVC scraps.

Mounting methods

Installation of plastic panels can not be called too complicated. According to experts, it is quite possible to cope with such work alone, since PVC sheets do not have much weight.
There are two main methods for installing such facing materials. The first one is the frame. Choosing a similar installation option, you should be ready to make a reliable and high-quality crate, to which plastic sheets will be attached. The second installation method is frameless. With this option, you do not have to make a separate frame, but you will need to carefully prepare the wall base for the future application of finishing materials. Otherwise, PVC panels will not hold firmly and securely to the ceiling.
It is worth considering in more detail how PVC sheets are installed in both cases.

On the frame

When you have completed the preparation of the rough floor, you can begin to prepare a high-quality frame. It can be made of metal or wood. Both options are quite reliable and durable. However, if you want to build a wooden structure, then it must be additionally treated with antiseptic agents to protect it from rotting and drying out.
Guide rails must be installed perpendicular to the PVC panels. Simply put, if you are going to mount the sheets horizontally, then the crate should be vertical and vice versa.
The frame slats should be mounted at a distance of 30 cm - this value is optimal in this case. These parts must be fixed at the beginning and end of the wall, as well as around door and window openings.

It is recommended to fasten the frame structure for plastic panels to the bases with dowels. 6x40 mm fasteners are inserted into the concrete floor (this is necessary so that a piece does not fall off on the other side of the concrete base), and 6x60 mm into the brick floor. Fasteners are recommended to be installed, adhering to an indent of 50-60 cm.

The crate must be set in the same plane- so the plastic sheathing will turn out to be even and neat. To achieve this effect, you can use small wooden linings or ordinary plywood pieces and install them under the frame planks. Do not forget that these elements also need to be treated with antiseptics.
It is also permissible to use special perforated hangers, which are usually used for plasterboard ceiling structures. Such elements are necessary for placing metal profiles in the same plane, but they can also be used in the case of wood frames.

If you plan to use plastic profiles for the construction of the frame, then you should consider one important nuance: these elements should only be perpendicular to the PVC panels. The slightest deviation can lead to many problems, for example, the clamps may not close and will not perform their main function. To avoid such errors, it is worth constantly checking the verticals and horizontals.
Also, experts advise installing wooden frame elements around the perimeter of the room. the same thickness as the PVC profiles, since the launch panels will be attached to these bases.
Further, at the level of the floor and ceiling, a starting or ceiling plinth should be used. The starting element is a narrow plastic strip. Ceiling plinth - a shaped part that has a special cutout.

Laying PVC profiles should begin in one of the corners(top or bottom). Finishing should be fastened to the frame slats. Fasteners are selected depending on the material that you used to construct the crate. The result is a design that resembles a frame. It is into it that the PVC panels will be inserted further.
Next, you need to cut the starting lamella in accordance with the length and height of the wall. To cut off excess pieces, you should use a hacksaw or a special saw for metal. When cutting the panel, do not press on it with your foot or hand too hard - you will push it or break it. In order for the first part to fit correctly in the right place, it is necessary to measure its length again. Subtract 4-5 cm from it and cut off.

At the starting strip, it is necessary to cut off the protruding spike. After that, with the cut side, this part must be inserted into the corner profile, tucking the edges into the upper and lower profiles. It is worth tapping lightly with your palm to drive the bar as deep as possible.

Be sure to apply a level to the edge of the installed element to check its evenness. If the part stands correctly, then you can safely fix it to each lath of the crate.

When you install the launch pad, you should cut the second one, dock it with the first one and fix it. Further actions are very simple and of the same type. Problems often arise only with the installation of the last lamella on the floor. Most often, this part has to be cut in width, after which you need to try to fill it at the same time in the groove and in the profile (starting or corner). This is not always possible to do neatly, because the plastic is easily wrinkled. To avoid such a problem, you should not install a second corner profile. In this case, this part is put on a fitted finish panel. Then these assembled elements are joined to the previous lamella. The profile is fixed only after these actions.

Further cladding of floors with PVC panels occurs in exactly the same way.
According to experienced finishers, the frame method of mounting plastic panels is reliable, but more complicated than frameless.

frameless

In cases where the floors are flat, plastered or sheathed with drywall, they do not require the installation of a crate for plastic finishing. In this case, it will only take away the free space in the room. On such bases, PVC panels are attached using silicone, liquid nails or mounting foam.

However, in this case, the launch panels will still have to be fixed to the walls with dowels.
After that, the following is applied to the back half of the sheets:
foam (it is better to lay it on PVC sheets in a zigzag pattern);
silicone (it is recommended to apply it on the panels in small portions at intervals of 10-15 cm).

Then the bar is inserted into the profiles and pressed tightly. After that, it is fixed with fasteners. Further, the installation of plastic panels should be continued according to the same principle.

The main advantage of this installation method is that it takes a minimum of free time. However, you can turn to it only if the walls in your home have a perfectly flat surface without serious flaws. It should be borne in mind that in the future it will hardly be possible to remove such a finish without damaging the plastic.

Cladding walls with plastic is not the most difficult job. The main thing is to follow the instructions provided and use quality materials / tools.
If you decide to make such Finishing work, you should take into account some recommendations from experts.
It is not recommended to combine PVC panels with more expensive materials. For example, the union of luxurious marble and PVC will look ridiculous and disharmonious.
According to experienced craftsmen, hot glue cannot be used for PVC.
To make a competent installation of the panels around the sockets, you must first make all the necessary holes for them in the material. Before doing this, be sure to turn off the electricity.

If you designed a wooden crate in the bathroom or in the kitchen, then a couple more millimeters must be added to the resulting indentation, since the wood is subject to deformation under the influence of dampness, moisture and temperature changes.
PVC panels are a popular and sought-after material, but they are not recommended to be installed in the bedroom (both for children and adults). For such rooms, it is better to choose more "breathable" materials.
It is not recommended to sheathe walls with PVC panels immediately after purchase. They should rest in a dry and warm room for at least 2 hours.
Wall decoration should be started only after the floor and ceiling are ready.
The advantages of PVC panels include their ability to hide various communications. However, these elements must still be available to hosts. To do this, use removable inserts.

If you use liquid nails to fasten PVC sheets, then you should not pull with the removal of their influxes - these compounds dry out very quickly.
Wall finishing materials should not have different openings at the joints. You need to follow this when choosing plastic panels.
At each stage of laying PVC panels, it is necessary to check the evenness of the structure using a level. This device will help to avoid bevels and curvature of the finish.
Experts recommend purchasing high-quality PVC panels. Do not look for too cheap coatings - such materials are already available. Ask the seller for quality certificates of paintings. Study them carefully. The composition of such finishing materials should not contain toxic compounds.

Design Options

PVC panels look organic in many settings. Designers do not recommend only combining such coatings in one ensemble with very expensive and pompous coatings (for example, natural stone). Against the background of such finishing materials, PVC sheets may seem too modest and even “poor”.
Plastic panels are able to enliven the interior of the hallway, corridor, living room, bathroom and kitchen. The main thing is to choose coatings of a suitable color and texture.
On the small kitchen in the loft style, the dining area can be distinguished by PVC panels imitating dark red brickwork. Against such a background, a laconic white table and metal chairs with dark colors will look harmonious. wooden backs and armrests. The dining area will look complete if you hang a large dark clock above the table.

PVC panels can be used to design an apron in the kitchen. For example, in a room with burgundy walls, a white floor and the same white set, an apron trimmed with a wide plastic sheet depicting coffee beans will look spectacular.

In the hallway, PVC panels are used most often. In such rooms, coatings imitating brick and stone look especially attractive. They are usually adjacent to ordinary wallpaper neutral colors. For example, canvases under a light brown stone will look harmonious in tandem with yellow wallpaper and a wooden front door.

Also, in the conditions of a hallway or a corridor, PVC panels with a silkscreen effect look good. Against the background of such light canvases, both entrance and interior doors dark shades. Such coatings look attractive, adjacent to wooden furniture and decor items.
With the help of PVC panels, you can revive the interior of the living room. In such environments, 3D coatings with embossed surfaces look especially original and stylish. For example, spectacular black textured canvases can be used to decorate an accent wall with a TV, and place a dark chocolate woven sofa opposite it. So that the ensemble does not seem too dark and oppressive, a light laminate should be placed on the floor.

Savings often become the main factor when choosing finishing materials for repairs. This explains the popularity of pvc panels. Manufacturers managed to combine seemingly incompatible things. Such as external attractiveness and democratic price. And add to this the ease of installation and we get an almost perfect finishing material.
In this article, we will talk about how to fix pvc panels to the wall, and we will talk about three ways to do it yourself.
The choice of how to attach pvc panels to the wall depends on many factors. Here is the humidity of the wall and the room and communications, and even the need to save space, which is especially important when it comes to finishing the toilet or bathroom, which are traditionally small.
It is not necessary to start from considerations of economy. The cheapest way is not always the best.
Below we will talk in detail about which mounting of pvc panels on the wall is best suited for a particular situation, but for now let's find out what difficulties we may encounter during the repair process:
Humidity of walls and bridges of cold. Plastic is not at all afraid of water and can be in constant contact with it, but it does not have vapor permeability at all, which means that over time, the moisture accumulating under the finish will begin to grow into a fungus or mold.
Availability of communications. You can still hide the wiring in the wall or, on the contrary, move it away, but water pipes(see How to ditch walls under pipes in several ways) or heating systems are much more difficult to hide, and sometimes even impossible.

Space saving. Below we will talk about fixing pvc panels to the wall through a bar. And this method can significantly reduce the area of \u200b\u200bthe room. Before you get started, consider whether you are ready to sacrifice a few cherished centimeters or not.
Curvature of the walls. Often there are so curved walls that it is very difficult to finish them. Here you have to either level the surface, or sacrifice centimeters and choose a mount through a beam.

Now that the main difficulties have been identified, inspect your room in which you are going to make repairs, and carefully read the article to the end in order to know exactly which pvc panel attachment to the wall is best for you.
Method 1: Liquid nails
The simplest and cheapest way to mount pvc panels to the wall, but only on the condition that you have perfectly even walls. Liquid nails are the unofficial name for a special silicone adhesive that dries very quickly and securely holds not only plastic, but also glass and wood.
Liquid nails are applied to the panels in even stripes, after which it is applied to the wall. The curing time of the glue is only a few minutes, so the entire repair will not take much time.
Despite the fact that the adhesive mounting method is the most economical and fastest, it is not always suitable, and experts advise using it with caution. The thing is that the panels are in direct contact with the wall, and as we said above, condensate will constantly accumulate on them, which simply has nowhere to evaporate from under the plastic.
Communication can also be a significant barrier. In the case of mounting on a beam, they may remain under the finish. Here, they will either have to be removed inside the wall, or silently pushed aside and let over the surface of the panels, which does not always look nice.
Important! fastening pvc pipes to the wall can also be done using liquid nails, but you need to choose a special, heat-resistant glue that does not liquefy when the temperature changes.

The evenness of the walls can also become an obstacle for this method of fastening. The difference should be no more than two centimeters, or the surface of the walls will have to be leveled with plaster, and these are additional financial costs.
Method 2: Nails, stapler, screws
Each pvc panel has a small tongue under the groove. It is in it that the fastening is made. You can use any convenient fastener, whether it be small shoe nails or a construction stapler. By the way, working with a stapler is much faster and more convenient.
A significant difficulty is the need to build a frame to which the panels are attached. Of course, if you are the owner of a wooden house and your walls are well protected from condensation, then you can do without it.
The frame is usually made from wooden blocks. It is easier to attach to them in any convenient way, but as an alternative, you can use a drywall profile, but here you will have to work only with self-tapping screws, since neither nails nor staples will simply hold on to the metal.
So, the first thing we need is to fix the bars to the wall. This can be done using dowels with plastic sleeves. Just lay the beam horizontally against the wall and drill a hole through it into the wall. Hammer the dowel and repeat the operation in increments of about 30-50 centimeters.
Important! Before you begin to fasten the bar, be sure to treat it with protective impregnations that will protect the tree from moisture, rotting and bugs. The better the wood is impregnated, the longer it will last.

The distance between the bars should also be no more than 50 centimeters, so that a deflection does not form on the panels, and they firmly support the weight if someone leans on the wall.
When the crate is ready, you can proceed to fixing the panels. They usually start from the right corner of the room. The first panel is fastened with a comb to the corner, and fasteners are hammered into the groove. The second side is fixed in the same way. Now we insert the next panel, and fasten it, but only in the groove, since it is already fixed on the side of the ridge.
Method 3: Kleimers
Kleimers are special brackets that are used to fasten any tongue-and-groove finishing materials. As you can see in the photo, the kleimer has a special fixing tongue, and a hole for a screw or nail. Working with them is very fast and convenient. Moreover, this is the only available way of fixing in a new house.
Walls built less than a year ago will shrink. It is imperceptible to the eye, and the finish can be reflected very strongly. Kleimers do not fix the panel, as they say, tightly, and allow for a slight curvature. As a result, the walls may sag while the panels remain in place.
If you do not quite understand how to attach pvc panels to the wall, then we suggest you watch the video in this article, which clearly shows the whole process. So, we figured out the three methods, but in order to make a high-quality fastening to the wall of a pvc panel, this knowledge is not enough. There are many nuances and subtleties of the process, which we will tell you about further.
So:
If you decide to treat the bar for the crate with impregnation, pre-cut it into right size. This way you can cover all parts, and even those that appear after cutting.
Before attaching to the wall pvc panels using liquid nails, make sure the surface is thoroughly dust-free. And most importantly, remove all grease or oil stains.
When choosing pvc panels in the store, be sure to pay attention to their smell. If the panels smell like chemicals, look for another manufacturer. It will be impossible to get rid of such amber.

If you use self-tapping screws for fastening, take only those that have a clamping cap. They do not tear the plastic and securely fix it to the base.
Plastic has slight thermal expansion, so when installing panels, leave small gaps near the floor and ceiling. To compensate for the deformation, 3 millimeters is enough, which will completely overlap with a decorative corner.

Using these simple rules, you can easily make repairs in your home that will delight you for many years.
And finally, I would like to add: in this article we have only superficially described the mounting methods, but if you need detailed instructions how to attach a pvc panel to a wall, then it is already on our website for sure.