Do-it-yourself summer shower from boards. Do-it-yourself summer shower - step-by-step instructions for building a shower room, from simple to complex. Options for shower designs for summer cottages

The optimal capacity is from 100 to 200 liters. Optionally, the roof can be covered galvanized metal or lay foil under the barrel - the sun's rays will be reflected from the polished surface and absorbed by the walls of the barrel, thereby accelerating the process of heating the water.

A plastic or metal pipe with faucet and watering can. To do this, a suitable hole is cut or drilled in the bottom of the barrel, through which a pipe is passed with external thread at the end. Rubber seals are laid on top and bottom, and then the pipe is tightened with a nut. The tap (valve) is installed using a tee, to the lower end of which a watering can is attached with or without a hose (depending on the wishes of the owner).

Door installation

At the final stage, the door is installed. Loops are used for fastening. Additionally, you can install an internal deadbolt and an external hook. Inside the cabin is equipped with hooks for towels and a hanging soap dish. On this construction works considered completed.

In the summer heat in the country, it is especially pleasant to take a cool or warm shower, wash off dust and fatigue. Believe me, especially if you yourself built a shower on the territory of your dacha.

Summer shower, made by myself and with love, is better than commercially available shower stalls - I can say this with full confidence. Such a shower can be sheathed with durable material with thermal insulation (often it is a wooden "lining", siding or board). They perfectly store heat, so they are successfully used in cold weather. This shower is already called a temporary structure with a big stretch.

Choosing a place for a country shower

It is necessary to start building your own soul in the country carefully and thoroughly. building country shower you need to start by choosing a platform for the shower. The best way if you build a shower in a sunny location (for planned solar water heating). You also need to consider the method of water supply, as well as its flow.

The shower is a room high humidity sometimes it attracts insects. For this reason, this building is recommended to be located away from country house, and at some distance from it. Most often, the structure of the soul is placed as close to the edge as possible. suburban area. To drain water, a gutter is dug on the site or, if possible, outside it.

Base and drain

At the site of the planned construction of the shower, you need to dig a small recess for the construction of its base. The recess is necessary to cover with a sheet of roofing material or PVC film, and even better to concrete it. Thus, you get a kind of waterproof "pan" that protects the soil under the shower from souring. From the pallet, the water should flow directly into the gutter. For this purpose, the pallet must be made with some slope. In order for the water to drain to a certain distance, you need to dig a trench under the sewer. In order for the water used in the shower to drain freely, it is imperative to maintain the direction of the slope of the pipe towards the pit, or in if you have already taken care to build it.

Cabin

The shower cabin is built of wood, always coniferous. A country shower is a fairly tall building (up to 3 meters) with a relatively small footprint. Such structures are rather unbalanced. For the frame of the walls, a bar measuring 100 by 100 millimeters is usually used. To build a more stable shower structure, it is better to concrete the base of the timber or dig it into the ground.

Remember to prevent rotting wooden beam in the soil, pre-wrap the bars in roofing material, glassine or tar. The installed support pillars from the timber are connected to each other along the top with a dressing from the same timber. Please note that the design of the shower must be durable, designed for a load of up to 200 kilograms. After completing the upper dressing, the lower one is made - it will also serve as a frame for the floor of the shower cabin. In its simplest form, the floor of the shower is made from a floor board, which is stuffed onto a frame with small gaps between the boards to drain water.

The walls are also sheathed with a board. Before you start working with, do not forget to cover the boards and beams with drying oil, which will protect the wood from dampness and decay. It is very important to provide a window for ventilation of the shower cabin when the door is closed. The same window will serve as lighting.

We heat water

As a container for water in country showers, barrels with a capacity of 100 to 200 liters are usually used. They are painted dark and mounted on the roof of the shower, as you know, this will allow the water to heat up faster. In addition, you can lay any reflective material on the roof (for example, foil or galvanization), which will also contribute to faster heating of the water. The tank must be equipped with a pipe with a faucet and a water diffuser.

It is very important to consider in advance how you are going to fill the tank with water. In the event that it is planned to fill the tank manually, it is necessary to attach a ladder to the shower roof.

Door

The final stage in the construction of a country shower is the installation of a door. Don't forget to wax and paint it too. After completion of all construction work, all wooden parts must be re-coated with a protective layer of paint. So go ahead - start building a shower in your country house, you will succeed. The pleasure of refreshing yourself by standing under your own rain is worth it.

Summer is a great time for summer holidays. It can be overshadowed by the absence of a shower, since a person, regardless of whether he works or rests, needs to perform water procedures.

If the cottage is used only in the summer, then the easiest way to organize a shower is on the site. You can make a mobile shower, or build a solid outbuilding.

Portable outdoor shower

In stores you can find a foot shower. It does not require any construction or installation to operate. As a rule, only a small container of water is needed to use it.

An existing hose is lowered into the tank, which is connected to the pump. It looks like a small rug. Water comes out through a hose with a watering can, and for it to go, a person just needs to stomp in one place.

This device is simply indispensable, as it is suitable not only for summer cottages, but also for picnics, you can take it with you on trips.

With its help, water procedures can be carried out not only on the street, but also in the house, when it is very cool outside.

To do this, you just need to put a basin and wash. Another advantage of a mobile shower is self-adjustment water temperature. Such a shower in the country is simply not replaceable.

Stationary shower

Many summer residents are interested in how to make a stationary shower. This option is quite expensive compared to the first one. However, it will serve you for many years.

Before starting construction, it is necessary to consider where the water will drain from it. It is good when there is an antiseptic on the site. It can be drained from the shower.

If it is absent, then you need to make a hole, fill the bottom with expanded clay. A family needs a pit measuring 60x60x60 cm.

If sand predominates in the soil, the walls of the recess will have to be strengthened so that they do not crumble. For this, a metal mesh or boards that are no longer needed are suitable.

shower base

As a rule, the shower building weighs little. Therefore, it makes no sense to make a foundation for it, it can be replaced with blocks. They are leveled at the same level so that the structure is level.

It is much cheaper than the foundation, and takes much less time to build, since the foundation must dry out, and the building can be erected immediately on the blocks.

Blocks should be placed 20 cm from the ground, this is necessary so that the tree does not rot.

In the event that you are going to make a metal structure, then the blocks can not be aligned at a level of 20 cm. Such a frame can be installed on ordinary paving slabs.

Building

There are two types of building. The first is when the building is divided into several parts. In one part, a shower is made, in the other, a locker room or a technical room where a boiler is installed.

Note!

The second type is a simple shower with a curtain, where only water procedures will be performed. Therefore, the dimensions of the soul are calculated from what kind of building is planned.

Frame types

Metal. The frame can be made of a profiled pipe, 3 mm in size. For work you need a welding machine.

Pipe joints are best welded, so the structure will be stronger. If the device is not available, then the joints can be fastened with special bolts.

Tree. For construction, you need a beam. Usually use a bar with a size of 50x50 mm. Before starting construction, it is necessary to make a drawing of the shower in the country.

shower sheathing

After the frame has been erected, the shower must be covered with material. There are no specific material standards. Everyone chooses according to his own pocket.

Let's highlight the most popular materials:

• oilcloth;
• the cloth;
• wood;
• slate;
• polycarbonate.

Water tank

Absolutely any container can be used as a tank. Basically, these are metal or plastic barrels. They can be purchased at any building, country stores.

Note!

When choosing, consider the region of residence. For southern cities, any container is suitable, but for the northern regions, only metal, as it heats up faster.

shower tray

It is best to purchase a pallet ready-made, as it will have a drain that will directly merge into the pit. The pallet is made of plastic or metal. Metal will last much longer, so it is advisable to choose it.

Making a summer shower in the country is not so difficult. The main thing is to thoroughly approach the design and calculate in advance the amount of material required.

For clarity, you can consider a photo of a summer soul in the country with your own hands. It will make your stay comfortable and enjoyable.

Do-it-yourself photo of the soul in the country

Note!

The owners of summer cottages are trying to bring water to the house and equip basic amenities. You can build a summer shower in the country with your own hands, both temporary and capital - the type of future structure is selected depending on individual needs.

Location selection

In order to ensure a quick drain of water, it is best to install the shower on a flat or slightly elevated area. You should not choose a site located in a strong lowland or in a pit.

To avoid stagnant water, choose the right place for building a summer shower

Optimal for a country shower will be open area, well lit by the sun, which is located at some distance from other buildings. In this case, the barrel will naturally heat up under the sun, providing a supply of warm water. This condition can be neglected only if it is planned to build a shower with heated water.

At the same time, the site where the construction will be carried out should not be too far from the house - after water procedures, it is desirable to get from the shower to the warm room.

Size calculation

When building a country shower, the following parameters are used as standard:

1. height - 200–300 cm;
2. length - 190 cm;
3. width - 140 cm.

An example of drawing up a drawing of a summer shower

The indicated dimensions are very convenient in that, taking into account the thickness of the walls, the building will ultimately come out with an area of ​​​​200x150 cm - this is a completely waste-free option when using boards standard sizes. As a result, 100x100 cm will be allocated for the shower stall, and 600x400 cm for the locker room.

Necessary tools and materials

You will need the following tools:

• roulette;
• corner;
• level;
• hammer.

In addition, you need to stock up on nails and a skein of twine. Separately, you need to purchase a tank, as well as pipes, a couple of taps and a shower divider. As a building material for the construction of the cabin, brick, iron or plastic sheets are suitable, wooden planks, for the construction of the frame - pipes.

Tools needed for building a shower in the country

For the foundation pouring and the erection of brickwork, a certain amount of cement, sand and concrete will be required, and for the final finish - insulation materials, paint, plaster, hooks for clothes, shelves for bathroom accessories and other accessories.

Options for shower designs for summer cottages

The easiest option for giving is a compact portable shower, which is suitable for one-time water procedures, has a standard volume of 20 liters and is designed to supply water for 10 minutes. The principle of operation is reduced to filling the reservoir with water and subsequent heating in the sun, after which the portable shower is attached to a height of 2 meters and is ready for use.

Portable shower

An open shower also has a simple design, the installation process of which boils down to the following steps:

1. fastening to the wall of a branch of a water pipe;
2. connecting a pipe and a watering can with a hose;
3. fixing the watering can holder;
4. screen installation.

A common option for a summer cottage is the so-called change house with a shower, the design of which assumes the presence of a one-piece modular container or a frame-collapsible block.

Options for a stationary summer shower for a summer residence

The installation of this design is quite simple - the territory is marked, the upper ball of soil is removed and leveled, a cushion of sand and gravel is created, on top of which the boards are laid. On the soil prepared in this way, a block assembled on site or a ready-made structure is installed.

Of course, a stationary shower will become the most solid, but it will take more time and effort to build it.

Foundation preparation

It is much easier to build a frame structure than a capital building - depending on the type of structure chosen, the stages of preparing the site for construction will differ.

For a temporary structure, it is enough to simply remove 10-15 cm of the top layer of soil from the site to level it, and then fill it with sand.

For a country capital soul, a foundation will be required, the depth of which is determined by the materials used for its construction. For example, for a brick shower, a foundation will be quite enough, the depth of which will reach 30 cm.

Foundation for the construction of a capital summer shower

The foundation is laid in the following sequence:

• pegs are driven into the outer corners of the future soul;
• a cord is pulled around the perimeter;
• a place is being prepared for pipes (a log or a branch wrapped in roofing material is laid);
• concrete mortar is poured.

Advice! The formwork equipment will allow extending the period of operation of the shower - it is recommended to raise the level of the entire foundation by 10 cm, raising it above the ground with the help of boards reinforced with stakes and spacers.

Drainage pit equipment

The volume of the pit is usually more than 2 cubic meters. m, while its walls must be strengthened in order to avoid possible scree. The drain is located a few meters from the shower, but not under the structure itself and not at its walls - this will lead to the destruction of the foundation in the future, as well as to the appearance of unwanted odors.

An example of equipment for a drain pit for a summer shower

The drain must be laid with a waterproof layer - roofing material, hydrostekloizol, PVC film or concrete screed (reinforced with a metal mesh) are used.

Attention! A common mistake is to use clay as an insulating material, which erodes and soon clogs the drainage ditch.

Installation of a frame for a temporary shower stall

If for a capital structure brickwork, then for the temporary, a frame is usually installed: metal or wooden. In the latter case, the tree should be treated with special impregnations that will protect it from insects and moisture, preventing the formation of fungus and mold.

Wooden frame for summer shower

1. Marking is done - a rectangle is indicated right on the ground, the sides of which correspond to the dimensions of the future country shower.
2. Wooden bars are installed, the width of which reaches up to 10 cm.
3. Ligation is performed - starting from the top, the structure is securely fastened with bolts, after which the beams-basis of the shower walls are connected.
4. Walls are equipped, for the construction of which you can use both boards and slate or plastic panels.
5. Piping is in progress - the plumbing is installed so that the outlet of the pipe under the shower hose is higher than the level of the head (this will provide the necessary pressure for the movement of water). For runoff, a conclusion is made to a sump or to a specially equipped septic tank.
6. A tank is installed - a tap is made with a thread, a tap with an appropriate nozzle is placed, after which the barrel rises and is fixed.

Suitable as a tank for a country shower plastic container, which can be purchased at a specialized store, or another barrel available on the farm. It is desirable that it be flat and proportionate to the area of ​​\u200b\u200bthe building, so that the weight is evenly distributed on the supporting structure. Its volume is selected at the rate of 40 liters per family member, but the barrel should not be too heavy - its maximum volume is not more than 200 liters!

solar water heating tank

Advice! So that the owner of the cottage does not have to carry water into the tank on his own every time, you can equip it with automatic filling.

Country shower lighting and ventilation

When doing the wiring yourself, it is important to follow all the rules of electrical installation and adhere to safety precautions. Separately, due to high humidity, care should be taken to insulate the wiring.

Ventilation window for summer shower

Interior shower trim should be made of moisture-resistant materials: plastic panels, pieces of linoleum, oilcloth, etc. If wood is used, then each individual board is covered with hot drying oil.

The concrete floor is usually covered with gratings made of plastic or wood, rubber mats are laid on top. It is quite convenient to equip a small locker room directly in the shower room. In order to prevent water from getting into it, the floors in it rise slightly by a couple of centimeters - this is easy to achieve by additionally placing a pallet.

Summer shower interior

Concerning exterior finish, then similar materials that have already been used to decorate a country house and other buildings on the site will look harmonious.

To use the shower not only in the summer, but also in the colder season, it is recommended to insulate it with polystyrene foam, which fits into the interior and is upholstered with PVC film on top. The walls are usually painted or plastered, sheathed with clapboard or siding.

How to build a summer shower in the country: video

Types of summer shower: photo

Against the background of a huge number of varieties of garden strawberries, the ampelous variety stands out. This strawberry with uncharacteristic pink, very decorative flowers is easily recognizable by both fruit-bearing mother plants and rosettes extending from them. After reviewing the care of her, having studied the rules of cultivation and looking at the photo, you can safely proceed to planting this unusual berry crop.

Features of ampelous strawberries

If an ordinary strawberry bears fruit once a season, a remontant two, then it can be said about an ampelous strawberry that it is able to bear fruit throughout the year.

Thanks to the work of breeders, ampelous strawberries grow before flower stalks are formed, flower buds are laid on them and, accordingly, an additional crop ripens. Further, the mustache itself continues to form the following. As a result, one bush can be continuously harvested.

In addition, this variety has excellent decorative qualities and can serve as a wonderful decoration for a balcony, veranda, etc.

Advice. For growing in a room, it is better to select varieties of neutral daylight hours that have a very long fruiting period.

In some sources, you can find it under the name "curly", but this is not entirely correct. By nature, strawberries cannot wrap themselves around anything. Some gardeners, for decorative purposes, simply tie a mustache with rosettes to a support. At the same time, it seems that the strawberry itself “climbs” up.

If you plant several bushes in a flowerpot or hanging pot, the rosettes will fall very beautifully from the mother plant, creating cascades of leaves, flowers and berries.

When considering the fruiting of ampelous varieties, it can be unequivocally stated that this is a remontant variety. On the bush at the same time you can see buds, flowers and berries. Thanks to this, in appropriate conditions, it is possible to observe flowering and pick berries almost all year round. Popular varieties:

• Homemade delicacy;
• Temptation;
• Tarpan;
• Elan;
• Novel;
• balcony stream;
• Balcony charm.

Almost all of them are hybrids that are adapted to growing in any conditions, resistant to some diseases and give a decent harvest. I would especially like to note the Tuscany variety. Despite its recent appearance, it has already gained worldwide recognition. Differs richly pink flowers and rather large fragrant berries.

Growing Options

If you show imagination and make very little effort, then bushes of ampelous strawberries can become a wonderful decoration for the site.

• Growing in pots and vases. In this case, any containers can be used for landing. For the normal development of the plant, their depth must be at least 30 cm. A mandatory requirement is holes for water drainage and a drainage layer. Seedlings intended for planting should be sprinkled with earth and kept for two weeks in a dark, cool place. Planting plants in a pot should not be too dense and not very deep.

Advice. Hand grown in hanging planter a lush strawberry bush can be a wonderful gift for a novice gardener.

• Grid growing. Can be used as a grid metal mesh, wicker fence, etc. Bushes are planted in the soil 30 cm apart. Growing mustaches are tied up along the lattice.

Advice. The height of the lattice should be selected no more than 1 m. So the plants will be able to completely cover it with fruit-bearing and flowering bushes at the same time.

• Landing in the form of a pyramid. For such a landing, you will need 3-4 boxes 30 cm high, without a bottom, of different sizes. The largest is placed on the ground in the garden and covered with fertile soil. A second, smaller one is placed on top and is also filled with earth. The smallest of them is placed on top. Soil is also poured into it. It turns out a cascade of boxes in which seedlings are planted. After growing, this structure looks like a green pyramid, covered with flowers and berries.
• Vertical beds. This method is used for growing ampelous strawberries in greenhouses. They are made from wide plastic pipes(diameter about 110 cm). Holes are cut into them after a certain interval, into which, after filling the pipe with nutrient soil, seedlings are planted.

How to plant seedlings

Planting ampelous varieties does not differ much from planting other types of strawberries.

1. The bottom of the pot or groove in the bed is lined with drainage material.
2. From above it is covered with nutrient soil, consisting of soddy soil, humus, manure and peat.
3. Well watered. After the soil settles, the earth is filled up.
4. Landing holes are being made.
5. One plant is distributed in each well.
6. The roots are pressed with wet earth so that the core remains at the top.

Advice. In order for the seedlings to take root faster, it is advisable to dip each rhizome in a clay mash.

How to care

Planted seedlings need frequent moisture. It should be watered 2 times a day a little. After 2 weeks, watering is reduced - it will be enough 1 time in 3 days. The first flower stalks are removed. So the plant will give all its strength to the development of the root system, which will make the plant strong.

Mustaches on each bush should remain no more than 5 pcs. All excess is plucked off. Top dressing is carried out regularly with mineral fertilizers.

Ampelous strawberry transplantation must be carried out every 3-4 years. In the spring, the antennae are plucked from the strongest bushes and transplanted to a new bed or into a new container. In the case of a flower bed, you can completely replace the soil and plants.

For the winter, you can not leave containers with strawberries on the street. All of them need to be brought into a warm room. If this is not possible, the container is dug into the ground and covered with a covering material.

For beds protruding above ground level, special frames are constructed, the surface of which is covered with roofing material, lutrasil, etc., and then sprinkled with something insulating, for example, sawdust, straw or hay.

Ampel strawberry is an amazing plant that can become a real decoration of a balcony, personal plot or rooms. And all this is combined with a long period of enjoyment of fragrant and tasty berries.

Features of planting ampelous strawberries: video